Nissan Teana J32. Instruction — part 992
REAR SEAT
SE-101
< ON-VEHICLE REPAIR >
[WITH VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Remove the headrest holder.
CAUTION:
Before installing headrest holder, check its orientation
(front/rear and right/left).
• Remove the hog rings, and then remove seatback center pad.
• Remove the hog rings to separate the seatback trim and seatback pad.
• Remove the seatback heater unit.
Assembly
Assemble in the reverse order of disassembly.
SEAT CUSHION
Disassembly
Remove the seat cushion trim.
• Remove the hog rings, and separate the seat cushion trim and seat cushion pad.
• Remove the seat cushion heater unit.
Assembly
Assemble in the reverse order of disassembly.
VENTILATION UNIT
Disassembly
1.
Remove the ventilation seat control unit.
• Disconnect the harness connectors (A).
• Remove the screws (B), and then remove ventilation seat con-
trol unit (1).
2.
Remove the seatback duct A.
Remove the nuts (B) and screw (C), and then remove seatback
duct A (1).
3.
Remove the seatback duct B ventilation motor (seatback).
PIIB4084J
JMJIA1940ZZ
JMJIA1941ZZ
SE-102
< ON-VEHICLE REPAIR >
[WITH VENTILATION SEAT]
REAR SEAT
• Disconnect the harness connector (A).
• Remove the screws (C), and then remove seatback duct B (1)
and ventilation motor (seatback) (2).
4.
Remove the seatback duct C.
• Remove the hob rings, and then remove seatback center pad.
• Remove the nuts (A), and then remove seatback duct C (1).
5.
Remove the seat cushion duct A.
Remove the nuts (B) and screw (C), and then seat cushion duct
A (1).
6.
Remove the seat cushion duct B and ventilation motor (seat cushion).
• Disconnect the harness connector (A).
• Remove the screws (C), and then remove seat cushion duct B
(1) and ventilation motor (seat cushion) (2).
Assembly
Assemble in the reverse order of disassembly.
JMJIA1942ZZ
JMJIA1943ZZ
JMJIA1944ZZ
JMJIA1945ZZ
POWER SEAT SWITCH
SE-103
< ON-VEHICLE REPAIR >
[WITH VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
POWER SEAT SWITCH
Exploded View
INFOID:0000000003849136
.
Removal and Installation
INFOID:0000000003849137
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1.
Remove the seat cushion outer finisher (1). Refer to
SE-92, "Removal and Installation"
2.
Remove switch knob.
3.
Remove screws (A).
4.
Remove the power seat switch (2) from the seat cushion outer
finisher.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to clump the harness to the right place.
JMJIA1952ZZ
SE-104
< ON-VEHICLE REPAIR >
[WITH VENTILATION SEAT]
HEATED SEAT SWITCH
HEATED SEAT SWITCH
FRONT SEAT
FRONT SEAT : Exploded View
INFOID:0000000003849128
FRONT SEAT : Removal and Installation
INFOID:0000000003849129
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect from damage.
1.
Remove the console switch finisher (2). Refer to
2.
Remove heated seat switch (driver side) (1) from console switch
finisher, with flat- bladed screw driver (A).
NOTE:
The same procedure is also performed for passenger side.
INSTALLATION
Install in the reverse order of removal.
REAR SEAT
1.
Heated seat switch (front seat)
2.
Console switch finisher
JMJIA1842ZZ
: Pawl
JMJIA1846ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст