Nissan Leaf. Instruction — part 1119
B0096 FRONT SIDE AIR BAG SATELLITE SENSOR RH
SRC-77
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
2. Check for DTC using CONSULT.
Is the DTC detected?
YES (Current DTC)>>Refer to
YES (Past DTC)>>GO TO 2.
NO
>> Inspection End.
2.
ERASE SELF-DIAG RESULT
Erase the DTC using CONSULT.
Can the DTC be erased?
YES
>> Inspection End.
NO
>> Refer to
DTC CONFIRMATION PROCEDURE (Without CONSULT)
1.
CHECK SELF-DIAG RESULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
Is the DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000010877000
1.
HARNESS CONNECTOR
Visually inspect all applicable harness connectors for the following:
• Visible damage to connector or terminal
• Loose terminal
• Poor connection
NOTE:
All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component
(including in-line connectors).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform one of the following repairs:
• Visible damage: Replace the harness.
• Loose terminal: Secure the terminal.
• Poor connection: Secure the connection.
2.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 3.
NO
>> Refer to
GI-53, "Intermittent Incident"
.
3.
WIRING HARNESS
Check the wiring harness for visible damage.
NOTE:
The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the harness.
4.
CONFIRM DTC
SRC-78
< DTC/CIRCUIT DIAGNOSIS >
B0096 FRONT SIDE AIR BAG SATELLITE SENSOR RH
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 5.
NO
>> Refer to
GI-53, "Intermittent Incident"
.
5.
SATELLITE SENSOR RH
1. Replace the satellite sensor RH. Refer to
SR-35, "Removal and Installation"
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 6.
NO
>> Clear DTC. Inspection End.
6.
AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace the air bag diagnosis sensor unit. Refer to
SR-38, "Removal and Installation"
.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 7.
NO
>> Clear DTC. Inspection End.
7.
RELATED HARNESS
Replace the related harness.
>> END
B0098 FRONT DOOR SATELLITE SENSOR RH
SRC-79
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B0098 FRONT DOOR SATELLITE SENSOR RH
Description
INFOID:0000000010877001
DTC B0098 FRONT DOOR SATELLITE SENSOR RH
The front door satellite sensor RH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor
unit will monitor the front door satellite sensor RH for internal failures and its circuits for communication errors.
PART LOCATION
SRC-6, "Component Parts Location"
.
DTC Description
INFOID:0000000010877002
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0098–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of front door satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
[B0098–23, B0098–24, B0098–25, B0098–28]
• Internal malfunction of front door satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
[B0098–81, B0098–93]
• Connection malfunction of harness or connector
• Internal malfunction of front door satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
[B0098–86]
• Air bag diagnosis sensor unit and front door satellite sensor RH is different from the part specified
[B0098–88]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of front door satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE (With CONSULT)
1.
CHECK SELF-DIAG RESULT
1. Turn ignition switch ON.
2. Check the DTC using CONSULT.
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0098–11
DOOR SATEL SENS RH
[Right Frontal Restraints
Sensor 3 (Subfault)]
[GND-SHORT]
Front door satellite sensor RH circuit is shorted to ground
B0098–23
[LOWER LIMIT ERR]
Lower limit value malfunction of front door satellite sensor RH
B0098–24
[UPPER LIMIT ERR]
Upper limit value malfunction of front door satellite sensor RH
B0098–25
[SELF-DIAG ERR]
Diagnosis malfunction of front door satellite sensor RH
B0098–28
[OFFSET ERR]
Offset malfunction of front door satellite sensor RH
B0098–81
[COMM ERR]
Communication malfunction of front door satellite sensor RH
B0098–86
[UNMATCH]
Front door satellite sensor RH is out of the specified specification
B0098–88
[OPEN]
Front door satellite sensor RH circuit is open
B0098–93
[RESET]
Reset malfunction of front door satellite sensor RH
SRC-80
< DTC/CIRCUIT DIAGNOSIS >
B0098 FRONT DOOR SATELLITE SENSOR RH
Is the DTC detected?
YES (Current DTC)>>Refer to
YES (Past DTC)>>GO TO 2.
NO
>> Inspection End.
2.
ERASE SELF-DIAG RESULT
Erase the DTC using CONSULT.
Can the DTC be erased?
YES
>> Inspection End.
NO
>> Refer to
DTC CONFIRMATION PROCEDURE (Without CONSULT)
1.
CHECK SELF-DIAG RESULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is the DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000010877003
NOTE:
Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is
eliminated using air bag warning lamp each time repair is finished. If malfunction is still observed, proceed to
the next step. When malfunction is eliminated, further repair work is not required.
1.
HARNESS CONNECTOR
Visually inspect all applicable harness connectors for the following:
• Visible damage to connector or terminal
• Loose terminal
• Poor connection
NOTE:
All harness connectors should be inspected from the air bag diagnosis unit to the end component (including
any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform one of the following repairs:
• Visible damage: Replace the harness.
• Loose terminal: Secure the terminal.
• Poor connection: Secure the connection.
2.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 3
NO
>> Refer to
GI-53, "Intermittent Incident"
.
3.
WIRING HARNESS
Check the wiring harness for visible damage.
NOTE:
The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст