Nissan Leaf. Instruction — part 405
CHARGE PORT LID OPENER RELAY
DLK-115
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CHARGE PORT LID OPENER RELAY
Diagnosis Procedure
INFOID:0000000010119800
Regarding Wiring Diagram information, refer to
.
1.
CHECK CHARGE PORT LID OPENER ACTUATOR RELAY POWER SUPPLY-1
1. Turn power switch OFF.
2. Disconnect charge port lid opener actuator relay.
3. Check the voltage between charge port lid opener actuator relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK CHARGE PORT LID OPENER ACTUATOR RELAY POWER SUPPLY-2
Check the voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK FUSE
1. Remove 20A fuse #43 from IPDM E/R.
2. Check that the fuse is not blown.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-29, "Removal and Installation"
.
NO
>> Replace the fuse after repairing the applicable circuit.
4.
CHECK CHARGE PORT LID OPENER ACTUATOR RELAY POWER SUPPLY CIRCUIT
1. Disconnect IPDM E/R harness connector.
2. Check the continuity between IPDM E/R harness connector and charge port lid opener actuator relay har-
ness connector.
3. Also check harness for short to ground and short to voltage.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-53, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning component.
+
−
Voltage
(Approx.)
Charge port lid opener actuator relay
Connector
Terminal
E88
5
Ground
12V battery voltage
+
−
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
E14
42
Ground
12V battery voltage
+
−
Continuity
IPDM E/R
Charge port lid opener actuator relay
Connector
Terminal
Connector
Terminal
E14
42
E88
5
Yes
DLK-116
< DTC/CIRCUIT DIAGNOSIS >
CHARGE PORT LID OPENER RELAY
5.
CHARGE PORT LID OPENER ACTUATOR RELAY CONTROL SIGNAL VOLTAGE
Check the voltage between charge port lid opener actuator relay harness connector under the following condi-
tion:
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 6.
6.
CHECK CHARGE PORT LID OPENER ACTUATOR RELAY DRIVE CIRCUIT
1. Disconnect VCM harness connector.
2. Check the continuity between VCM harness connector and charge port lid opener actuator relay harness
connector.
3. Also check harness for short to ground and short to voltage.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace malfunctioning component.
7.
CHECK CHARGE PORT LID OPENER SWITCH RELATED CIRCUIT
Check charge port lid opener switch related circuit. Refer to
DLK-120, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-53, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning component.
8.
CHECK CHARGE PORT LID OPENER ACTUATOR RELAY GROUND CIRCUIT
Check the continuity between charge port lid opener actuator relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace malfunctioning component.
Component Inspection (Charge Port Lid Opener Actuator Relay)
INFOID:0000000010119801
1.
CHECK CHARGE PORT LID OPENER ACTUATOR RELAY
1. Turn power switch OFF.
2. Disconnect charge port lid opener actuator relay.
+
−
Condition
Voltage
(Approx.)
Charge port lid opener
actuator relay
Connector
Terminal
E88
1
Ground
Immediately after the charge port lid opener switch is
pressed.
12V battery voltage
+
−
Continuity
VCM
Charge port lid opener actuator relay
Connector
Terminal
Connector
Terminal
E61
23
E88
1
Yes
+
−
Continuity
Charge port lid opener actuator relay
Connector
Terminal
E88
2
Ground
Yes
CHARGE PORT LID OPENER RELAY
DLK-117
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Check the continuity between charge port lid opener actuator
relay terminals under the following conditions:
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace charge port lid opener actuator relay.
Termi-
nals
Conditions
Continuity
3 and 5
12 V direct current supply between terminals 1 and 2
Yes
No current supply
No
PIIA2636J
DLK-118
< DTC/CIRCUIT DIAGNOSIS >
CHARGE PORT LID OPENER
CHARGE PORT LID OPENER
Component Function Check
INFOID:0000000010119802
1.
CHARGE PORT LID OPENER FUNCTION CHECK
1. Close charge port lid.
2. Press charge port lid opener switch.
Does the charge port lid open?
YES
>> Inspection End.
NO
>> Proceed to
EVC-395, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010119803
Regarding Wiring Diagram information, refer to
.
1.
CHECK CHARGE PORT LID OPENER ACTUATOR RELAY RELATED CIRCUIT
Check charge port lid opener actuator relay related circuit. Refer to
DLK-115, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning component.
2.
CHECK CHARGE PORT LID OPENER ACTUATOR
Check charge port lid opener actuator. Refer to
DLK-119, "Component Inspection (Charge Port Lid Opener
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace charge port lid opener actuator. Refer to
DLK-191, "CHARGE PORT LID OPENER
ACTUATOR : Removal and Installation"
3.
CHECK CHARGE PORT LID OPENER ACTUATOR CONTROL CIRCUIT
1. Check the continuity between charge port lid opener actuator relay harness connector and charge port lid
opener actuator harness connector.
2. Also check harness for short to ground and short to voltage.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning component.
4.
CHECK CHARGE PORT LID OPENER ACTUATOR GROUND CIRCUIT
Check the continuity between charge port lid opener actuator harness connector and ground.
Is the inspection result normal?
YES
>> Inspection End.
+
−
Continuity
Charge port lid opener actuator relay
Charge port lid opener actuator
Connector
Terminal
Connector
Terminal
E88
3
E38
3
Yes
+
−
Continuity
Charge port lid opener actuator relay
Connector
Terminal
E88
2
Ground
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст