Nissan Leaf. Instruction — part 404
REMOTE KEYLESS ENTRY RECEIVER
DLK-111
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
>> Inspection End.
DLK-112
< DTC/CIRCUIT DIAGNOSIS >
UNLOCK SENSOR
UNLOCK SENSOR
Component Function Check
INFOID:0000000010119795
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “UNLK SEN -DR” in “Data Monitor”.
3. Check that the function operates normally according to the following conditions:
Is the inspection result normal?
YES
>> Unlock sensor is OK.
NO
>> Refer to
DLK-112, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010119796
Regarding Wiring Diagram information, refer to
.
1.
CHECK BCM OUTPUT SIGNAL
1. Turn power switch OFF.
2. Disconnect front door lock assembly (LH) connector.
3. Check signal between front door lock assembly (LH) harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK UNLOCK SENSOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and front door lock assembly (LH) harness connector.
3. Check continuity between BCM harness connector and ground.
Monitor item
Condition
Status
UNLK SEN -DR
Driver side door
Lock
OFF
Unlock
ON
(+)
(–)
Signal
(Reference value)
Front door lock assembly (LH)
Connector
Terminal
D38
3
Ground
PKIB4960J
BCM
Front door lock assembly (LH)
Continuity
Connector
Terminal
Connector
Terminal
M24
31
D38
3
Yes
BCM
Ground
Continuity
Connector
Terminal
M24
31
No
UNLOCK SENSOR
DLK-113
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-72, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock assembly (LH) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK UNLOCK SENSOR
DLK-113, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly (LH). Refer to
DLK-192, "DOOR LOCK : Removal and Installa-
.
5.
CHECK INTERMITTENT INCIDENT
GI-53, "Intermittent Incident"
.
>> Inspection End.
Component Inspection
INFOID:0000000010119797
1.
CHECK UNLOCK SENSOR
1. Turn power switch OFF.
2. Disconnect front door lock assembly (LH) connector.
3. Check continuity between front door lock assembly (LH) terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace front door lock assembly (LH). Refer to
DLK-192, "DOOR LOCK : Removal and Installa-
.
Front door lock assembly (LH)
Ground
Continuity
Connector
Terminal
D38
4
Yes
Front door lock assembly (LH)
Condition
Continuity
Terminal
3
4
Driver side door
Unlock
Yes
Lock
No
DLK-114
< DTC/CIRCUIT DIAGNOSIS >
INFORMATION DISPLAY
INFORMATION DISPLAY
Component Function Check
INFOID:0000000010119798
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “LCD” in “Active Test”.
3. Check each warning display on meter display.
Is the inspection result normal?
YES
>> Information display is OK.
NO
>> Refer to
DLK-114, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010119799
1.
CHECK COMBINATION METER
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-53, "Intermittent Incident"
>> Inspection End.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст