Nissan Leaf. Instruction — part 861

POWER SWITCH ILLUMINATION CIRCUIT

INL-49

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

INL

N

O

P

POWER SWITCH ILLUMINATION CIRCUIT

Description

INFOID:0000000010122280

Provides the power supply and the ground to control the power switch illumination.

Component Function Check

INFOID:0000000010122281

1.

CHECK POWER SWITCH ILLUMINATION OPERATION

CONSULT ACTIVE TEST

1. Turn the power switch ON.

2. Select “ENGINE SW ILLUMI” in “Active Test” of “BCM (INTELLIGENT KEY)”.

3. While operating the test items, check that the power switch illumination turns ON/OFF.

Does the power switch illumination turn ON/OFF?

YES

>> Power switch illumination circuit is normal.

NO

>> Refer to

INL-49, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010122282

Regarding Wiring Diagram information. Refer to

INL-28, "Wiring Diagram"

.

1.

CHECK POWER SWITCH ILLUMINATION POWER SUPPLY OUTPUT

1. Turn power switch OFF.

2. Disconnect power switch connector.

3. Check voltage between power switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

CHECK POWER SWITCH ILLUMINATION POWER SUPPLY OPEN CIRCUIT

1. Disconnect BCM connector.

2. Check continuity between BCM harness connector and the power switch harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harnesses.

3.

CHECK POWER SWITCH ILLUMINATION POWER SUPPLY SHORT CIRCUIT

Check continuity between BCM harness connector and ground.

On

: Power switch illumination ON

Off

: Power switch illumination OFF

(+)

(–)

Condition

Voltage

(Approx.)

Power switch

Connector

Terminal

M33

5

Ground

Power switch illumination

ON

Battery voltage

OFF

0 V

BCM

Power switch

Continuity

Connector

Terminal

Connector

Terminal

M23

90

M33

5

Yes

INL-50

< DTC/CIRCUIT DIAGNOSIS >

POWER SWITCH ILLUMINATION CIRCUIT

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-72, "Removal and Installation"

.

NO

>> Repair or replace harnesses.

4.

CHECK POWER SWITCH ILLUMINATION GROUND CIRCUIT

1. Check continuity between power switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace power switch.

NO

>> Repair or replace harnesses.

BCM

Ground

Continuity

Connector

Terminal

M23

90

No

Power switch

Ground

Continuity

Connector

Terminal

M33

6

Yes

INTERIOR LIGHTING SYSTEM SYMPTOMS

INL-51

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

INL

N

O

P

SYMPTOM DIAGNOSIS

INTERIOR LIGHTING SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000010122283

CAUTION:

Perform the “Self Diagnostic Result” with CONSULT before the symptom diagnosis. Perform the trou-

ble diagnosis if any DTC is detected.

Symptom

Possible cause

Inspection item

All the following lamps do not turn ON:
• Map lamp
• Room lamp
• Luggage room lamp

• Harness between BCM and each

interior room lamp

• BCM

Interior room lamp power supply cir-
cuit
Refer to

INL-44

.

• Interior room lamp does not turn ON even

though the door is open.
(It turns ON when turning the interior room
lamp ON.)

• Interior room lamp does not turn OFF even

though the door is closed.

• Harness between BCM and each

door switch

• Harness between BCM and each

interior room lamp

• BCM

Door switch circuit
Refer to

DLK-102

.

Interior room lamp control circuit
Refer to

INL-46

.

Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/closes.)

—

Check the interior room lamp setting.
Refer to

INL-10, "INTERIOR ROOM

LAMP BATTERY SAVER SYSTEM :
System Description"

.

• Luggage room lamp does not turn ON even

though the back door is open.

• Luggage room lamp does not turn OFF even

though the back door is closed.

• Harness between BCM and back

door switch

• Harness between BCM and lug-

gage room lamp

• BCM

Back door switch circuit
Refer to

DLK-102

.

Luggage room lamp circuit
Refer to

INL-48

.

Power switch illumination does not illuminate.

• Harness between BCM and power

switch

• BCM

Power switch illumination circuit
Refer to

INL-49

.

Interior room lamp battery saver does not acti-
vate.

BCM

Replace BCM.
Refer to

BCS-72

.

INL-52

< REMOVAL AND INSTALLATION >

MAP LAMP

REMOVAL AND INSTALLATION

MAP LAMP

Removal and Installation

INFOID:0000000010122284

CAUTION:

• Disconnect the 12V battery negative terminal or remove power circuit fuse while performing the

operation to prevent electric leakage. Refer to

INL-3, "Precaution for Removing 12V Battery"

.

• Do not attempt to separate the map lamp assembly from the headlining prior to removing headlining,

or damage to the components may occur.

REMOVAL

1. Remove the headlining. Refer to

INT-37, "Removal and Installation"

.

2. Remove the two bracket screws, then remove the map lamp assembly bracket from the map lamp assem-

bly and position aside.

3. Disconnect the harness connectors from the map lamp assembly.
4. Release the back plate pawls using a suitable tool and remove the map lamp assembly.

CAUTION:

When removing, support the map lamp assembly by hand so it does not fall out and get damaged

during removal.

5. Remove the map lamp back plate from the headlining.

INSTALLATION

Installation is in the reverse order of removal.

Replacement

INFOID:0000000010122285

MAP LAMP BULB

The map lamp LED bulbs are replaced as part of the map lamp.