Nissan Leaf. Instruction — part 686
FRONT DRIVE SHAFT
FAX-25
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Secure boot band so that dimension (A) meets the specifi-
cation as shown in the figure.
12. Check that displacement does not occur when boot is rotated
with the joint sub-assembly and shaft fixed.
CAUTION:
• Reinstall them using boot bands when boot installation
positions become incorrect.
• Never reuse boot band.
REDUCTION GEAR SIDE
REDUCTION GEAR SIDE : Disassembly and Assembly
INFOID:0000000010121671
DISASSEMBLY
Left Side
1. Fix shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2. Remove boot bands, and then remove boot from housing.
3. Put matching marks on housing and shaft, and then pull out housing from shaft.
CAUTION:
Use paint or an equivalent for matching marks. Never scratch the surfaces.
4. Put matching marks (A) on the spider assembly and shaft.
CAUTION:
Use paint or an equivalent for matching marks. Never
scratch the surfaces.
5. Remove snap ring (1), and then remove spider assembly from
shaft.
6. Remove boot from shaft.
7. Remove dust shield from housing.
8. Remove circular clip from housing.
9. Perform inspection after disassembly. Refer to
Right Side
1. Fix shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2. Remove boot bands, and then remove boot from housing.
3. Put matching marks on housing and shaft, and then pull out housing from shaft.
CAUTION:
Use paint or an equivalent for matching marks. Never scratch the surfaces.
A
: 7.0 mm (0.276 in) or less.
JPDIF0268ZZ
JPDIF0006ZZ
JPDIF0014ZZ
FAX-26
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT DRIVE SHAFT
4. Put matching marks (A) on the spider assembly and shaft.
CAUTION:
Use paint or an equivalent for matching marks. Never
scratch the surfaces.
5. Remove snap ring (1), and then remove spider assembly from
shaft.
6. Remove boot from shaft.
7. Remove support bearing, follow the procedure described below.
a. Remove dust shield from housing.
b. Remove snap ring (1).
JPDIF0006ZZ
JPDIF0014ZZ
YAX002
JPDIF0106ZZ
FRONT DRIVE SHAFT
FAX-27
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
c. Press out support bearing from housing.
d. Remove dust shield from housing.
8. Perform inspection after disassembly. Refer to
ASSEMBLY
Left Side
1. Clean the old grease on housing assembly with paper waste.
2. Install dust shield to housing.
CAUTION:
Never reuse dust shield.
3. Install circular clip to housing.
CAUTION:
Never reuse circular clip.
4. Install new boot and boot bands to shaft.
CAUTION:
• Wrap serration on shaft with tape (A) to protect boot from
damage.
• Never reuse boot and boot bands.
5. Remove the tape wrapped around the serration on shaft.
6. To install the spider assembly (1), align it with the matching
marks (A) on the shaft (2) during the removal, and direct the ser-
ration mounting surface (B) to the shaft.
7. Secure spider assembly onto shaft with snap ring (1).
CAUTION:
Never reuse snap ring.
8. Apply the appropriate amount of grease to spider assembly and
sliding surface.
9. Assemble the housing onto spider assembly, and apply the bal-
ance of the specified amount grease.
10. Align matching marks put during the removal of housing.
YAX004
JPDIF0009ZZ
JPDIF0017ZZ
Grease amount
JPDIF0014ZZ
FAX-28
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT DRIVE SHAFT
11. Install boot securely into grooves (indicated by “*” marks) shown
in the figure.
CAUTION:
If grease adheres to the boot mounting surface (with “*”
marks) on shaft or housing, boot may be removed. Remove
all grease from the surface.
12. To prevent the deformation of the boot, adjust the boot installa-
tion length to the value by inserting the suitable tool into the
inside of boot from the large diameter side of boot and discharg-
ing inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.
• Be careful not to touch the inside of the boot with the tip of tool.
13. Install boot bands securely.
CAUTION:
Never reuse boot bands.
a. Put boot band in the groove on drive shaft boot. Then fit pawls into holes to temporary installation.
NOTE:
For the large diameter side, fit projection (A) and guide slit (B) at
first.
b. Pinch projection on the band with suitable pliers to tighten band.
c.
Insert the tip of band into the lower part of pawl (marked with
dotted circle) as shown in the figure.
14. Check that displacement does not occur when boot is rotated
with the housing assembly fixed.
CAUTION:
• If displacement occurs, reinstall band.
• Never reuse boot band.
Right Side
1. Install support bearing, follow the procedure described below.
a. Install dust shield to housing.
CAUTION:
Never reuse dust shield.
L
: Boot installation length
Boot installation length : Refer to
.
JSDIA2063ZZ
JPDIF0157ZZ
JPDIF0158ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст