Nissan Leaf. Instruction — part 1058
REAR SEAT
SE-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Seatback assembly (RH)
5. Remove center seat belt finisher (seatback assembly (LH) only).
a. Pull up on front of center seat belt finisher, then release pawls.
b. Pull up on sides of center seat belt finisher, release pawls and
remove.
: Pawl
6. Release the headrest holder locks as shown and remove the
headrest holders.
CAUTION:
Before removing/installing the headrest holder, check its
orientation (front/rear and right/left).
7. Rotate the seatback latch release knob counterclockwise and
remove.
JMJIA8359ZZ
JMJIA5062ZZ
PIIB4084J
JMJIA4374ZZ
SE-40
< REMOVAL AND INSTALLATION >
REAR SEAT
8. Reach up through seatback pad and remove the seatback latch
release knob finisher as shown.
CAUTION:
When installing seatback lock knob finisher, check front
and rear orientation and be careful to install it normally.
9. Remove seatback trim and seatback pad as an assembly.
10. Remove hog rings and separate the seatback trim from the seatback pad.
NOTE:
Remove all hog rings and discard them.
11. Remove seatback latch assembly bolts and the seatback latch assembly.
12. Remove center seat belt retractor. Refer to
SB-16, "SEAT BELT RETRACTOR : Removal and Installa-
ASSEMBLY
Assemble is in the reverse order of disassembly.
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat-
back trim and seatback pad wires.
• Use NISSAN standard hog rings and tools to assemble.
SEAT CUSHION
SEAT CUSHION : Removal and Installation
INFOID:0000000010122966
REMOVAL
CAUTION:
When removing the seat cushion, do not damage the rear seat heater harness and harness connector.
1. Lift up the seat cushion assembly close to the front edge (B) to release it from the seat cushion hooks (A)
(one for each side) and remove the seat cushion assembly.
: Front
CAUTION:
Do not use excessive force to front of seat cushion assembly when removing.
To avoid damage, lift seat cushion assembly closest to seat cushion hooks.
JMJIA4375ZZ
PIIB3356J
JMJIA4835ZZ
REAR SEAT
SE-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
2. Pull out seat belt buckle from seat cushion assembly.
3. Lift up seat cushion assembly, and then disconnect the rear seat
heater harness connector (A) and unclip the harness from the
seat cushion assembly.
: Clip
4. Remove seat cushion assembly from vehicle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• If center seat belt buckle (1) and seat belt buckle RH (2) are not installed in normal position, the seat
belt cannot be fastened. After seat cushion assembly installation, check that center seat belt buckle
is positioned as shown.
SEAT CUSHION : Disassembly and Assembly
INFOID:0000000010122967
DISASSEMBLY
1. Remove the seat cushion assembly. Refer to
SE-40, "SEAT CUSHION : Removal and Installation"
.
2. Remove the hog rings and separate the seat cushion trim from the seat cushion pad.
NOTE:
Remove all pieces of hog rings and discard them.
ASSEMBLY
Assemble is in the reverse order of disassembly.
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat
cushion trim and seat cushion pad wires.
• Use NISSAN standard hog rings and tools to assemble.
SEATBACK HINGE
SEATBACK HINGE : Removal and Installation
INFOID:0000000010122968
Seatback hinge bracket (center)
JMJIA8360ZZ
JMJIA7317ZZ
PIIB3356J
SE-42
< REMOVAL AND INSTALLATION >
REAR SEAT
REMOVAL
1. Remove seatback assembly (LH/RH). Refer to
SE-37, "SEATBACK : Removal and Installation"
.
2. Remove seatback hinge bracket (center) bolts and remove.
INSTALLATION
1. Temporarily tighten all bolts, then tighten bolts to specification in
.
: Front
Seatback hinge bracket (LH/RH)
REMOVAL
1. Remove seatback assembly. Refer to
SE-37, "SEATBACK : Removal and Installation"
2. Remove seatback hinge bracket finisher.
a. Pull seatback hinge finisher in direction shown (
) and release
at locations (A).
b. Then lift in direction shown (
) and remove.
3. Remove bolt (A) and the seatback hinge bracket.
JMJIA8361ZZ
JMJIA8362ZZ
JMJIA8363ZZ
JMJIA8364ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст