Nissan Leaf. Instruction — part 705
GI-32
< PRECAUTION >
PRECAUTIONS
• If old rubber hose is re-used, install hose clamp in its original posi-
tion (at the indentation where the old clamp was). If there is a trace
of tube bulging left on the old rubber hose, align rubber hose at
that position.
• Discard old clamps; replace with new ones.
• After installing plate clamps, apply force to them in the direction of
the arrow, tightening rubber hose equally all around.
Air Conditioning
INFOID:0000000010122915
Use an approved refrigerant recovery unit any time the air conditioning system must be discharged. Refer to
HA section “REFRIGERANT” for specific instructions.
SMA021D
SMA022D
CAUTIONS AS TO HIGH VOLTAGE
GI-33
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
B
GI
N
O
P
CAUTIONS AS TO HIGH VOLTAGE
How to Disconnect High Voltage
INFOID:0000000010122916
PROCEDURE FOR DISCONNECTING HIGH VOLTAGE
Be sure to follow the procedure below and disconnect the high voltage before performing inspection or servic-
ing of the high voltage system.
1. Turn power switch OFF.
CAUTION:
The worker must keep the intelligent key on his/her person.
2. Disconnect 12V battery negative terminal.
3. Remove service plug, following below procedure.
a. Insert a suitable tool under the RH rear corner of the access trim
cover (1) and pry up (2) to remove.
b. Remove the access cover bolts (1) and remove the cover (2).
c. Remove the service plug.
DANGER:
Touching high voltage components without using the appropriate protective equipment will
cause electrocution.
WARNING:
• Immediately insulate removed high voltage connectors and terminals with insulating tape.
• Be sure to put the removed service plug in your pocket and carry it with you so that another per-
son does not accidentally connect it while work is in progress.
:Vehicle front
ALAIA0106ZZ
:Vehicle front
ALAIA0107ZZ
ALAIA0088ZZ
GI-34
< PRECAUTION >
CAUTIONS AS TO HIGH VOLTAGE
4. Wait for a minimum of approximately 10 minutes after the service plug is removed.
PROCEDURE FOR CONNECTING HIGH VOLTAGE
1. Check that 12V battery negative terminal is disconnected.
2. Install service plug as per the following steps.
DANGER:
Touching high voltage components without using the appropriate protective equipment will
cause electrocution.
WARNING:
• Immediately insulate removed high voltage connectors and terminals with insulating tape.
• Be sure to put the removed service plug in your pocket and carry it with you so that another per-
son does not accidentally connect it while work is in progress.
3. Connect 12V battery negative terminal.
High Voltage Precautions
INFOID:0000000010122917
WARNING:
• Because hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of elec-
tric shock, electric leakage, or similar accidents if the high voltage component and vehicle are han-
dled incorrectly. Be sure to follow the correct work procedures when performing inspection and
maintenance.
• Be sure to remove the service plug in order to shut off the high voltage circuits before performing
inspection or maintenance of high voltage system harnesses and parts.
• To prevent the removed service plug from being connected by mistake during the procedure, always
carry it in your pocket or put it in the tool box.
• Be sure to wear insulating protective equipment consisting of glove, shoes, face shield, and glasses
before beginning work on the high voltage system.
• Clearly identify the persons responsible for high voltage work and ensure that other persons do not
touch the vehicle. When not working, cover high voltage parts with an insulating cover sheet or sim-
ilar item to prevent other persons from contacting them.
CAUTION:
There is the possibility of a malfunction occurring if the vehicle is changed to READY status while the
service plug is removed. Therefore do not change the vehicle to READY status unless instructed to do
so in the Service Instruction.
HIGH VOLTAGE HARNESS AND EQUIPMENT IDENTIFICATION
The colors of the high voltage harnesses and connectors are all orange. Orange “High Voltage” labels are
applied to the Li-ion battery and other high voltage devices. Do not carelessly touch these harnesses and
parts.
HANDLING OF HIGH VOLTAGE HARNESS AND TERMINALS
Immediately insulate disconnected high voltage connectors and terminals with insulating tape.
REGULATIONS ON WORKERS WITH MEDICAL ELECTRONICS
WARNING:
ALAIA0089ZZ
CAUTIONS AS TO HIGH VOLTAGE
GI-35
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
B
GI
N
O
P
The vehicle contains parts that contain powerful magnets. If a person who is wearing a heart pace-
maker or other medical device is close to these parts, the medical device may be affected by the mag-
nets. Such persons must not perform work on the vehicle.
PROHIBITED ITEMS TO CARRY DURING THE WORK
Because this vehicle uses components that contain high voltage and powerful magnetism, do not carry any
metal products which may cause short circuits, or any magnetic media (cash cards, prepaid cards, etc.) which
may be damaged on your person when working.
POSTING A SIGN OF “DANGER! HIGH VOLTAGE AREA. KEEP OUT”
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст