Nissan Leaf. Instruction — part 704
GI-28
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Description
INFOID:0000000010122906
Observe the following precautions to ensure safe and proper servicing. These precautions are not
described in each individual section.
Precaution for Technicians Using Medical Electric
INFOID:0000000010122907
OPERATION PROHIBITION
WARNING:
• Parts with strong magnet is used in this vehicle.
• Technicians using a medical electric device such as pacemaker must never perform operation on the
vehicle, as magnetic field can affect the device function by approaching to such parts.
NORMAL CHARGE PRECAUTION
WARNING:
• If a technician uses a medical electric device such as an implantable cardiac pacemaker or an
implantable cardioverter defibrillator, the possible effects on the devices must be checked with the
device manufacturer before starting the charge operation.
• As radiated electromagnetic wave generated by on board charger at normal charge operation may
effect medical electric devices, a technician using a medical electric device such as implantable car-
diac pacemaker or an implantable cardioverter defibrillator must not enter the vehicle compartment
(including luggage room) during normal charge operation.
PRECAUTION AT TELEMATICS SYSTEM OPERATION
WARNING:
• If a technician uses implantable cardiac pacemaker or implantable cardioverter defibrillator (ICD),
avoid the device implanted part from approaching within approximately 220 mm (8.66 in) from inte-
rior/exterior antenna.
• The electromagnetic wave of TCU might affect the function of the implantable cardiac pacemaker or
the implantable cardioverter defibrillator (ICD), when using the service, etc.
• If a technician uses other medical electric devices than implantable cardiac pacemaker or implant-
able cardioverter defibrillator (ICD), the electromagnetic wave of TCU might affect the function of the
device. The possible effects on the devices must be checked with the device manufacturer before
TCU use.
PRECAUTION AT INTELLIGENT KEY SYSTEM OPERATION
WARNING:
• If a technician uses implantable cardiac pacemaker or implantable cardioverter defibrillator (ICD),
avoid the device implanted part from approaching within approximately 220 mm (8.66 in) from inte-
rior/exterior antenna.
• The electromagnetic wave of intelligent key might affect the function of the implantable cardiac
pacemaker or the implantable cardioverter defibrillator (ICD), at door operation, at each request
switch operation, or at engine starting.
• If a technician uses other medical electric devices than implantable cardiac pacemaker or implant-
able cardioverter defibrillator (ICD), the electromagnetic wave of intelligent key might affect the func-
tion of the device. The possible effects on the devices must be checked with the device
manufacturer before intelligent key use.
Point to Be Checked Before Starting Maintenance Work
INFOID:0000000010122908
The high voltage system may starts automatically. It is required to check that the timer air conditioner
and timer charge (during EVSE connection) are not set before starting maintenance work.
NOTE:
If the timer air conditioner or timer charge (during EVSE connection) is set, the high voltage system starts
automatically even when the power switch is in OFF state.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRECAUTIONS
GI-29
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
B
GI
N
O
P
PRE-TENSIONER"
INFOID:0000000010409358
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000010122911
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precaution for Removing 12V Battery
INFOID:0000000010122912
1. Check that EVSE is not connected.
NOTE:
If EVSE is connected, the air conditioning system may be automatically activated by the timer A/C func-
tion.
2. Turn the power switch OFF
→ ON → OFF. Get out of the vehicle. Close all doors (including back door).
3. Check that the charge status indicator lamp does not blink and wait for 5 minutes or more.
NOTE:
If the battery is removed within 5 minutes after the power switch is turned OFF, plural DTCs may be
detected.
4. Remove 12V battery within 1 hour after turning the power switch OFF
→ ON → OFF.
NOTE:
• The 12V battery automatic charge control may start automatically even when the power switch is in
OFF state.
• Once the power switch is turned ON
→ OFF, the 12V battery automatic charge control does not start for
approximately 1 hour.
CAUTION:
PIIB3706J
GI-30
< PRECAUTION >
PRECAUTIONS
• After all doors (including back door) are closed, if a door (including back door) is opened before
battery terminals are disconnected, start over from Step 1.
• After turning the power switch OFF, if “Remote A/C” is activated by user operation, stop the air
conditioner and start over from Step 1.
General Precautions
INFOID:0000000010122913
• Before jacking up the vehicle, apply wheel chocks or other tire
blocks to the wheels to prevent the vehicle from moving. After jack-
ing up the vehicle, support the vehicle weight with safety stands at
the points designated for proper lifting before working on the vehi-
cle.
These operations should be done on a level surface.
• When removing a heavy component such as the engine or tran-
saxle/transmission, be careful not to lose your balance and drop
them. Also, do not allow them to strike adjacent parts, especially
the brake tubes and master cylinder.
• Before starting repairs which do not require battery power:
Turn off power switch.
Disconnect the negative battery terminal.
• If the battery terminals are disconnected, recorded memory of
radio and each control unit is erased.
• To prevent serious burns:
Avoid contact with hot metal parts.
Do not remove the radiator cap when the engine is hot.
• Dispose of drained oil or the solvent used for cleaning parts in an
appropriate manner.
• Do not attempt to top off the fuel tank after the fuel pump nozzle
shuts off automatically.
Continued refueling may cause fuel overflow, resulting in fuel spray
and possibly a fire.
• Clean all disassembled parts in the designated liquid or solvent
prior to inspection or assembly.
• Replace oil seals, gaskets, packings, O-rings, locking washers,
cotter pins, self-locking nuts, etc. with new ones.
• Replace inner and outer races of tapered roller bearings and needle bearings as a set.
• Arrange the disassembled parts in accordance with their assembled locations and sequence.
• Do not touch the terminals of electrical components which use microcomputers (such as ECM).
Static electricity may damage internal electronic components.
• After disconnecting vacuum or air hoses, attach a tag to indicate the proper connection.
• Use only the fluids and lubricants specified in this instruction.
• Use approved bonding agent, sealants or their equivalents when required.
SGI231
SEF289H
SGI233
PRECAUTIONS
GI-31
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
B
GI
N
O
P
• Use hand tools, power tools (disassembly only) and recommended
special tools where specified for safe and efficient service repairs.
• When repairing the fuel, oil, water, vacuum or exhaust systems,
check all affected lines for leakage.
• Before servicing the vehicle:
Protect fenders, upholstery and carpeting with appropriate covers.
Take caution that keys, buckles or buttons do not scratch paint.
WARNING:
To prevent ECM from storing the diagnostic trouble codes, do not carelessly disconnect the harness
connectors which are related to the engine control system and TCM (transmission control module)
system. The connectors should be disconnected only when working according to the WORK FLOW of
TROUBLE DIAGNOSES in EC and TM sections.
Hoses
INFOID:0000000010122914
HOSE REMOVAL AND INSTALLATION
• To prevent damage to rubber hose, do not pry off rubber hose with
tapered tool or screwdriver.
• To reinstall the rubber hose securely, check that hose insertion
length and orientation is correct. (If tube is equipped with hose
stopper, insert rubber hose into tube until it butts up against hose
stopper.)
HOSE CLAMPING
JPAIA0335ZZ
SGI234
SMA019D
SMA020D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст