Nissan Leaf. Instruction — part 423
HOOD LOCK
DLK-187
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD LOCK
Exploded View
INFOID:0000000010119885
HOOD LOCK
HOOD LOCK : Removal and Installation
INFOID:0000000010119886
REMOVAL
1. Remove radiator upper grille. Refer to
DLK-165, "RADIATOR UPPER GRILLE : Removal and Installa-
2. Remove hood lock assembly. Refer to
DLK-187, "HOOD LOCK : Removal and Installation"
.
3. Disconnect hood lock control cable (2) from hood lock assembly
(1).
4. Disconnect the harness connector from the hood lock assembly (if equipped).
5. Remove the hood lock assembly.
INSTALLATION
1.
Hood lock secondary control
2.
Hood lock assembly
3.
Hood lock control cable
A.
To charge port lid lock
Clip
Grease
AWKIA2419ZZ
JMKIA6504ZZ
DLK-188
< REMOVAL AND INSTALLATION >
HOOD LOCK
Installation is in the reverse order of removal.
CAUTION:
• Check that hood lock control cable is properly engaged with hood lock.
• After installation, perform hood assembly adjustment procedure. Refer to
• After installation, perform hood lock control inspection. Refer to
.
HOOD LOCK SECONDARY CONTROL
HOOD LOCK SECONDARY CONTROL : Removal and Installation
INFOID:0000000010119887
REMOVAL
Remove the hood lock secondary control nuts and hood lock secondary control.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, perform hood lock control inspection. Refer to
.
HOOD LOCK CONTROL CABLE
HOOD LOCK CONTROL CABLE : Removal and Installation
INFOID:0000000010119888
REMOVAL
1. Disconnect the hood lock control cable from the hood lock assembly.
2. Disconnect the charge port lid control cable from the charge port lid lock.
3. Disconnect the hood lock control cable and charge port lid control cable from the hood lock release han-
dle and charge port lid lock release handle.
4. Remove the fender protector (LH). Refer to
EXT-21, "FENDER PROTECTOR : Removal and Installation"
.
5. Release hood lock control cable clips using a suitable tool.
6. Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.
CAUTION:
While pulling, do not damage the outside of hood lock control cable.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not bend cable too much, keep the radius 100 mm (3.937 in) or more.
• Check that cable is not offset from the positioning grommet
and apply sealant to the grommet (at * mark).
• Check that hood lock control cable is properly engaged with hood lock.
• After installation, perform hood assembly adjustment procedure. Refer to
• After installation, perform hood lock control inspection. Refer to
.
Inspection
INFOID:0000000010119889
NOTE:
If the hood lock release cable is bent or deformed, replace it.
PIIB5801E
HOOD LOCK
DLK-189
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1. Check that secondary latch is properly engaged with secondary striker with hoods own weight.
2. While operating hood lock release lever, carefully check that the front end of the hood is raised by approx-
imately 20.0 mm (0.79 in). Also check that the hood lock release lever returns to the original position.
3. Check that the hood lock release lever operates at 49 N (5.0 kg-m, 11.0 ft-lb) or below.
4. Install so that the static closing force of the hood is 120 - 564 N (12.2 - 57.6 kg-m, 89 - 416 ft-lb).
NOTE:
• Do not exert vertical force on the right or left side of hood lock.
• Do not press simultaneously on both sides.
5. Check the hood lock lubrication condition. If necessary, apply a
suitable multi-purpose grease.
: Grease point
JMKIA6506ZZ
DLK-190
< REMOVAL AND INSTALLATION >
CHARGE PORT LID LOCK
CHARGE PORT LID LOCK
Exploded View
INFOID:0000000010119890
CHARGE PORT LID LOCK
CHARGE PORT LID LOCK : Removal and Installation
INFOID:0000000010119891
REMOVAL
1. Remove charge port lid rear cover. Refer to
2. Disconnect charge port lid control cable (2) from charge port lid
lock (1), as shown.
3. Remove charge port lid lock bolts and charge port lid lock.
1.
Charge port lid cover assembly
2.
Charge port lid seal
3.
Charge port lid assembly
4.
Charge port lid lock cable
5.
Charge port lid actuator assembly
6.
Charge port lid
7.
Charge port lid lock
8.
Charge port lid rear cover
Clip
AWKIA2416ZZ
JMKIA6507ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст