Nissan Leaf. Instruction — part 693
FRONT STABILIZER
FSU-21
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• To install stabilizer clamp bolt, follow the tightening method and the
numerical order shown below:
• To install stabilizer connecting rod (1), tighten the nut with the hex-
agonal part (A) on the stabilizer connecting rod side fixed.
• Perform final tightening of fixing parts at the vehicle installation
position (rubber bushing), under unladen conditions with tires on
level ground.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000010119440
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
Check wheel alignment. Refer to
Instruction tightening
: 1
Temporary tightening
: 2
→ 3
Final tightening (Specified torque)
: 4
→ 5
: Front
JPEIA0245GB
JPEIA0252ZZ
FSU-22
< REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000010119441
Removal and Installation
INFOID:0000000010119442
WARNING:
• Because hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of elec-
tric shock, electric leakage, or similar accidents if the high voltage component and vehicle are han-
dled incorrectly. Be sure to follow the correct work procedures when performing inspection and
maintenance.
• Be sure to remove the service plug in order to disconnect the high voltage circuits before perform-
ing inspection or maintenance of high voltage system harnesses and parts.
• To prevent the removed service plug from being connected by mistake during the procedure, always
carry it in your pocket or put it in the tool box.
• Be sure to wear insulating protective equipment consisting of glove, shoes, face shield and glasses
before beginning work on the high voltage system.
• Clearly identify the persons responsible for high voltage work and ensure that other persons do not
touch the vehicle. When not working, cover high voltage parts with an insulating cover sheet or sim-
ilar item to prevent other persons from contacting them. Refer to
GI-33, "How to Disconnect High
CAUTION:
There is the possibility of a malfunction occurring if the vehicle is changed to READY status while the
service plug is removed. Therefore do not change the vehicle to READY status unless instructed to do
so in the Service Instruction.
REMOVAL
WARNING:
Disconnect high voltage circuit. Refer to
GI-33, "How to Disconnect High Voltage"
.
1. Check voltage in high voltage circuit. (Check that condenser are discharged.)
a. Lift up the vehicle and remove the Li-ion battery under covers. Refer to
b. Disconnect high voltage harness connector from front side of Li-ion battery. Refer to
1.
Front suspension member
2.
Rebound stopper rubber
3.
Insulator
4.
Member stay
5.
Rebound stopper
: N·m (kg-m, ft-lb)
JPEIA0275GB
FRONT SUSPENSION MEMBER
FSU-23
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
c. Measure voltage between high voltage harness terminals.
DANGER:
Touching high voltage components without using the
appropriate protective equipment will cause electrocution.
CAUTION:
For voltage measurements, use a tester which can measure to 500 V or higher.
2. Remove 12V battery. Refer to
FSU-5, "Precaution for Removing 12V Battery"
.
3. Remove front under cover. Refer to
EXT-23, "FRONT UNDER COVER : Removal and Installation"
.
4. Remove traction motor inverter. Refer to
TMS-103, "Removal and Installation"
5. Remove the bolts (A), then remove the compressor stay (1).
WARNING:
To prevent electric shock hazards, be sure to wear
protective gear.
6. Disconnect the high voltage harness connector (A) from electric
compressor.
WARNING:
•
To prevent electric shock hazards, be sure to wear
protective gear.
• Protect the terminals of disconnected high voltage har-
ness connector with insulation tape so that they are not
exposed.
• Follow the procedure below and disconnect the high voltage harness connector.
Standard
: 5 V or less
JSAIA1362ZZ
JPIIA1763ZZ
JPIIA1764ZZ
JPCIA0037ZZ
FSU-24
< REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
7. Disconnect the low voltage harness connector (A) from electric
compressor.
WARNING:
To prevent electric shock hazards, be sure to wear
protective gear.
8. Remove electric compressor (1). Hang electric compressor not
to interfere with work.
WARNING:
To prevent electric shock hazards, be sure to wear
protective gear.
CAUTION:
Do not apply excessive stress to high-pressure flexible
hose and low-pressure flexible hose.
9. Remove ground cable (1) from compressor bracket (2).
WARNING:
To prevent electric shock hazards, be sure to wear
protective gear.
10. Remove traction motor harness connector (1).
WARNING:
To prevent electric shock hazards, be sure to wear
protective gear.
JPIIA1765ZZ
: Front
JPEIA0278ZZ
: Front
JPEIA0279ZZ
2
: Water hose (lower side)
: Front
JPEIA0280ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст