Nissan Leaf. Instruction — part 692
TRANSVERSE LINK
FSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
TRANSVERSE LINK
Exploded View
INFOID:0000000010119435
Removal and Installation
INFOID:0000000010119436
REMOVAL
1. Remove wheel and tire using power tool. Refer to
2. Separate stabilizer connecting rod from strut assembly. Refer to
FSU-19, "Removal and Installation"
3. Separate steering outer socket from steering knuckle. Refer to
ST-41, "Removal and Installation"
.
4. Remove transverse link from steering knuckle using power tool. Refer to
5. Remove transverse link from suspension member using power tool.
NOTE:
To remove transverse link nut, move stabilizer bar.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Do not reuse transverse link nuts.
• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000010119437
INSPECTION AFTER REMOVAL
Check the following items, and replace the parts if necessary.
Transverse Link
• Transverse link and bushing for deformation, cracks or damage.
• Ball joint boot for cracks or other damage, and also for grease leakage.
Swing Torque
1. Instructionly move ball stud to confirm it moves smoothly with no binding.
1.
Front suspension member
2.
Transverse link
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JPEIA0286GB
FSU-18
< REMOVAL AND INSTALLATION >
TRANSVERSE LINK
2. Move ball stud at least ten times by hand to check for smooth movement.
3. Hook a spring balance (A) at cutout on ball stud (B). Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
• If swing torque exceeds standard range, replace transverse link
assembly.
Axial End Play
1. Move ball stud at least ten times by hand to check for smooth movement.
2. Move tip of ball stud in axial direction to check for looseness.
• If axial end play exceeds the standard value, replace transverse link assembly.
INSPECTION AFTER INSTALLATION
Check wheel alignment. Refer to
Swing torque
: Refer to
.
Measurement on
spring balance
: Refer to
JPEIA0138ZZ
Axial end play
: Refer to
FRONT STABILIZER
FSU-19
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
FRONT STABILIZER
Exploded View
INFOID:0000000010119438
Removal and Installation
INFOID:0000000010119439
REMOVAL
1. Remove wheel and tire using power tool. Refer to
2. Separate intermediate shaft from steering gear assembly.Refer to
ST-38, "Removal and Installation"
3. Remove front under cover. Refer to
EXT-23, "FRONT UNDER COVER : Removal and Installation"
.
4. Remove Li-ion battery under cover (front). Refer to
.
5. Remove fender protector. Refer to
EXT-21, "FENDER PROTECTOR : Removal and Installation"
6. Remove stabilizer connecting rod.
7. Remove steering outer socket from steering knuckle. Refer to
ST-41, "Removal and Installation"
.
8. Separate transverse link from steering knuckle using power tool. Refer to
.
9. Set suitable jack under reduction gear and traction motor.
CAUTION:
• Do not damage the reduction gear and traction motor with
a jack.
• Check the stable condition when using a jack.
1.
Stabilizer bar
2.
Stabilizer clamp
3.
Stabilizer bushing
4.
Stabilizer connecting rod
5.
Strut assembly
6.
Front suspension member
: N·m (kg-m, ft-lb)
JPEIA0287GB
JSEIA0333ZZ
FSU-20
< REMOVAL AND INSTALLATION >
FRONT STABILIZER
10. Separate high voltage harness clip from bracket.
11. Remove motor mounting rear bolt. Refer to
12. Remove motor mounting (LH and RH) bolts from front suspen-
sion member. Refer to
TMS-109, "Removal and Installation"
13. Remove member stay and rebound stopper using power tool.
14. Remove suspension member bolts, washer, and rebound stop-
per rubber using power tool. Refer to
15. Remove front suspension member from vehicle body.
CAUTION:
Check the stable condition when using a jack.
16. Remove bolts (
) of stabilizer clamp, and then remove stabi-
lizer clamp and stabilizer bushing from front suspension mem-
ber using power tool.
17. Remove stabilizer bar.
18. Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install stabilizer clamp and stabilizer bush with notch (A) and slit
(B) faced forward of the vehicle (
).
: Front
JSEIA0331ZZ
: Front
JSEIA0332ZZ
WEIA0182E
JPEIA0058ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст