Nissan Leaf. Instruction — part 425
FRONT DOOR LOCK
DLK-195
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
9. Remove front gasket (1) and rear gasket (2).
10. Slide outside handle bracket toward rear of vehicle to remove.
11. Disconnect outside handle cable (1) from outside handle bracket
(2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When installing key rod, rotate key rod holder until a click is felt (driver side only).
• Check that door lock cables are properly engaged with inside handle and outside handle.
• After installation, check door open/close and lock/unlock operation.
Pawl
Front
AWKIA2412ZZ
Front
JMKIA6416ZZ
JMKIA6417ZZ
DLK-196
< REMOVAL AND INSTALLATION >
REAR DOOR LOCK
REAR DOOR LOCK
Exploded View
INFOID:0000000010119897
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010119898
REMOVAL
1. Remove outside handle bracket. Refer to
DLK-197, "OUTSIDE HANDLE : Removal and Installation"
1.
Outside handle escutcheon
2.
Rear gasket
3.
Outside handle bracket
4.
Bolt
5.
Door lock assembly
6.
Inside handle escutcheon
7.
Inside handle
8.
Cable clip
9.
Front gasket
10. Outside handle
Front
Do not reuse
Grease
AWKIA2932ZZ
REAR DOOR LOCK
DLK-197
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Disengage inside handle cable (1) from cable clip (A).
3. Remove lower bolt (B) of partition sash.
4. Disconnect the harness connector from the door lock actuator.
5. Remove door lock assembly bolts.
6. Remove door lock assembly while locating Inside handle cable and door lock cable to the bottom side of
rear partition sash.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door lock assembly bolts.
• After installation, check the door open/close and lock/unlock operation.
• After installation, check door lock cable is properly engaged with outside handle bracket.
• Check door lock assembly for poor lubrication. If necessary,
apply a suitable multi-purpose grease.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000010119899
REMOVAL
1. Remove rear door finisher. Refer to
INT-22, "Removal and Installation"
.
2. Remove inside handle screws and inside handle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check door open/close and lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010119900
REMOVAL
1. Fully close rear door glass.
JMKIA9363ZZ
: Grease point
JMKIA5892ZZ
DLK-198
< REMOVAL AND INSTALLATION >
REAR DOOR LOCK
2. Remove rear door finisher. Refer to
INT-22, "Removal and Installation"
.
3. Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
4. Remove door side grommet and loosen bolt from grommet hole.
5. While pulling outside handle, remove outside handle escutch-
eon.
6. While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
7. Remove front gasket (1) and rear gasket (2).
JMKIA1467ZZ
JMKIA5342ZZ
JMKIA0524ZZ
Pawl
Front
AWKIA2412ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст