Nissan Leaf. Instruction — part 635
REAR COMBINATION LAMP
EXL-141
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
• Fogging of rear combination lamp inside is not a malfunction. Never replace parts. Fogging is a
symptom in which inner surface of lens becomes whitely clouded, without there being visible water
drops or water spots, as if lens is made of frosted-glass.
REMOVAL
1. Remove luggage side lower finisher. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER : Removal
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting bolts.
4. Insert a shop cloth (B) into clearance (A) between rear combination lamp (1) and rear fender panel (2), or
apply protective tape.
CAUTION:
• To prevent rear fender panel paint surface from being damaged, always apply protection using a
shop cloth or protective tape.
• When using protective tape, apply protective tape to both rear fender panel and rear combination
lamp.
5. Pull rear combination lamp toward vehicle rear side, as shown
by the arrow in the figure.
6. Remove rear combination lamp.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
JMLIA2386ZZ
: Clip
JMLIA2385ZZ
EXL-142
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
REAR COMBINATION LAMP
When installing rear combination lamp, fix harness using harness fixing hook (A) on backside of rear
combination lamp housing and place harness toward vehicle inside so that harness is not pinched by
rear fender panel.
Replacement
INFOID:0000000010121404
CAUTION:
• Disconnect the 12V battery negative terminal or remove the fuse. Refer to
.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP BULB
LED is used for stop/tail lamp bulb. Always replace rear combination lamp assembly as a unit, when bulb is to
be replaced because of malfunction.
REAR TURN SIGNAL LAMP BULB
1. Remove rear combination lamp mounting bolts.
2. Insert a shop cloth (B) into clearance (A) between rear combination lamp (1) and rear fender panel (2), or
apply protective tape.
CAUTION:
• To prevent rear fender panel paint surface from being damaged, always apply protection using a
shop cloth or protective tape.
1.
Harness
2.
Rear fender panel
3.
Rear fender extension
4.
Rear inner panel
: Vehicle front
JMLIA2387ZZ
REAR COMBINATION LAMP
EXL-143
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
• When using protective tape, apply protective tape to both rear fender panel and rear combination
lamp.
3. Pull rear combination lamp toward vehicle rear side, as shown
by the arrow in the figure.
4. Rotate bulb socket counterclockwise and unlock it.
5. Remove bulb from the socket.
BACK-UP LAMP BULB
1. Remove rear combination lamp mounting bolts.
2. Insert a shop cloth (B) into clearance (A) between rear combination lamp (1) and rear fender panel (2), or
apply protective tape.
CAUTION:
• To prevent rear fender panel paint surface from being damaged, always apply protection using a
shop cloth or protective tape.
• When using protective tape, apply protective tape to both rear fender panel and rear combination
lamp.
JMLIA2386ZZ
: Clip
JMLIA2385ZZ
JMLIA2386ZZ
EXL-144
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
REAR COMBINATION LAMP
3. Pull rear combination lamp toward vehicle rear side, as shown
by the arrow in the figure.
4. Rotate bulb socket counterclockwise and unlock it.
5. Remove bulb from the socket.
: Clip
JMLIA2385ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст