Nissan Frontier D40. Instruction — part 790
BCM (BODY CONTROL MODULE)
INL-115
< ECU DIAGNOSIS >
[WITHOUT POWER DOOR LOCKS]
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
DTC Inspection Priority Chart
INFOID:0000000005550772
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
DTC Index
INFOID:0000000005550773
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF
→
ON again.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→
2
→
3...38
→
39 after returning to the normal condition whenever ignition switch OFF
→
ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF
→
ON after returning to the normal condition if the malfunction is detected again.
Display contents of CONSULT
Fail-safe
Cancellation
U1000: CAN COMM CIRCUIT
Inhibit engine cranking
When the BCM re-establishes communication with the other mod-
ules.
Priority
DTC
1
• U1000: CAN COMM CIRCUIT
2
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
3
• C1729: VHCL SPEED SIG ERR
• C1735: IGNITION SIGNAL
4
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1712: [CHECKSUM ERR] FL
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1720: [CODE ERR] FL
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR
• C1727: [BATT VOLT LOW] RL
CONSULT display
Fail-safe
Tire pressure
monitor warning
lamp ON
Reference page
No DTC is detected.
further testing
may be required.
—
—
—
U1000: CAN COMM CIRCUIT
—
—
INL-116
< ECU DIAGNOSIS >
[WITHOUT POWER DOOR LOCKS]
BCM (BODY CONTROL MODULE)
B2190: NATS ANTTENA AMP
—
—
B2191: DIFFERENCE OF KEY
—
—
B2192: ID DISCORD BCM-ECM
—
—
B2193: CHAIN OF BCM-ECM
—
—
C1708: [NO DATA] FL
—
—
C1709: [NO DATA] FR
—
—
C1710: [NO DATA] RR
—
—
C1711: [NO DATA] RL
—
—
C1712: [CHECKSUM ERR] FL
—
—
C1713: [CHECKSUM ERR] FR
—
—
C1714: [CHECKSUM ERR] RR
—
—
C1715: [CHECKSUM ERR] RL
—
—
C1716: [PRESSDATA ERR] FL
—
—
C1717: [PRESSDATA ERR] FR
—
—
C1718: [PRESSDATA ERR] RR
—
—
C1719: [PRESSDATA ERR] RL
—
—
C1720: [CODE ERR] FL
—
—
C1721: [CODE ERR] FR
—
—
C1722: [CODE ERR] RR
—
—
C1723: [CODE ERR] RL
—
—
C1724: [BATT VOLT LOW] FL
—
—
C1725: [BATT VOLT LOW] FR
—
—
C1726: [BATT VOLT LOW] RR
—
—
C1727: [BATT VOLT LOW] RL
—
—
C1729: VHCL SPEED SIG ERR
—
—
C1735: IGNITION SIGNAL
—
—
—
CONSULT display
Fail-safe
Tire pressure
monitor warning
lamp ON
Reference page
INTERIOR LIGHTING SYSTEM SYMPTOMS
INL-117
< SYMPTOM DIAGNOSIS >
[WITHOUT POWER DOOR LOCKS]
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000005272861
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
Symptom
Possible cause
Inspection item
interior room lamps do not turn ON/OFF
• Front room/map lamp assembly (if equipped)
• Room lamp 2nd row
• Harness between fuse block (J/B)
and each interior room lamp
• Harness between each interior
room lamp and door switches
• Door switches
Interior room lamp
Refer to
.
Cargo lamp does not turn ON/OFF
• Harness between fuse block (J/B)
and cargo lamp relay
• Harness between cargo lamp relay
and cargo lamp
• Harness between BCM and cargo
lamp relay
• BCM
Cargo lamp control circuit
Refer to
.
INL-118
< PRECAUTION >
[WITHOUT POWER DOOR LOCKS]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005567995
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
General precautions for service operations
INFOID:0000000005272863
• When removing or disassembling any part, be careful not to damage or deform it. Protect parts which may
get in the way with cloth.
• When removing parts with a screw driver or other tool, protect parts by wrapping them with vinyl or tape.
• Keep removed parts protected with cloth.
• If an non-reuseable part is removed, replace it with a new one.
• After re-assembly has been completed, make sure each part functions correctly.
• Never work with wet hands.
• Turn the lighting switch OFF before disconnecting and connecting the connector.
• Do not use organic solvent (paint thinner or gasoline) to clean lamps or remove sealant residue.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст