Nissan Frontier D40. Instruction — part 1095
TM-278
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
OIL PAN
OIL PAN
Removal and Installation
INFOID:0000000005589592
REMOVAL AND INSTALLATION
Removal
1.
Drain A/T fluid. Refer to
TM-263, "Changing the A/T Fluid
2.
Remove oil pan bolts.
3.
Remove oil pan and gasket.
4.
Check for foreign materials in oil pan to help determine cause of malfunction. If the A/T fluid is very dark,
has some burned smell, or contains foreign particles then friction material (clutches, band) may need
replacement. A tacky film that will not wipe clean indicates varnish build up. Varnish can cause valves,
servo, and clutches to stick and can inhibit pump pressure.
CAUTION:
If friction material is detected, flush the transmission cooler after repair. Refer to
5.
Remove magnets from oil pan.
Installation
1.
Install the oil pan magnets as shown.
SCIA2308E
SCIA5200E
SCIA5200E
OIL PAN
TM-279
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Install the oil pan with new oil pan gasket.
CAUTION:
• Be sure the oil drain plug is located to the rear of the
transmission assembly.
• Before installing oil pan bolts, remove any traces of old
sealant from the sealing surfaces and threaded holes.
• Do not reuse old gasket, replace with a new one.
• Always replace the oil pan bolts as they are self-sealing.
• Partially install the oil pan bolts in a criss-cross pattern to
prevent dislocation of the gasket.
3.
Tighten oil pan bolts in numerical order as shown.
4.
Refill the A/T with fluid and check for fluid leakage. Refer to
TM-261, "Checking the A/T Fluid (ATF)"
.
SCIA2308E
Oil pan bolts
: 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA4113E
TM-280
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
CONTROL VALVE WITH TCM
CONTROL VALVE WITH TCM
Removal and Installation
INFOID:0000000005274206
COMPONENTS
REMOVAL
1.
Disconnect negative battery terminal.
2.
Drain A/T fluid. Refer to
TM-263, "Changing the A/T Fluid (ATF)"
.
3.
Disconnect A/T assembly harness connector.
1.
Transmission
2.
Snap ring
3.
Sub-harness
4.
Control valve with TCM
5.
Bracket
6.
A/T fluid temperature sensor 2
7.
Oil pan gasket
8.
Oil pan bolt
9.
Oil pan
10. Magnet
11.
Drain plug
12. Drain plug gasket
13. Terminal cord assembly
14. O-ring
15. O-ring
16. Plug
A/T fluid temperature sensor 2 (A) can be changed to plug (B), depending on vehicles.
JSDIA1431GB
CONTROL VALVE WITH TCM
TM-281
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Remove snap ring from A/T assembly harness connector.
5.
Push A/T assembly harness connector.
CAUTION:
Do not damage connector.
6.
Remove oil pan and oil pan gasket. Refer to
TM-278, "Removal and Installation"
.
7.
If an A/T fluid temperature sensor 2 is attached, disconnect the A/T fluid temperature sensor 2 connector
as shown below.
a.
Disconnect A/T fluid temperature sensor 2 connector (A).
CAUTION:
Do not damage connector.
b.
Straighten the four terminal clips (
) to free the terminal cord
assembly for A/T fluid temperature sensor 2 harness.
8.
Straighten terminal clip (
) to free the output speed sensor har-
ness.
9.
Disconnect output speed sensor connector (1).
CAUTION:
Do not damage connector.
SCIA5021E
SCIA5022E
SCIA8124E
JSDIA1316ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст