Nissan Frontier D40. Instruction — part 828
ENGINE OIL
LU-23
< ON-VEHICLE MAINTENANCE >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
CAUTION:
The refill capacity depends on the oil temperature and drain time. Use the “Refill oil capacity” val-
ues as a reference and check the oil level using the dipstick when filling the engine with oil.
6.
Warm up the engine and check the area around the drain plug and oil filter for any oil leaks.
7.
Stop the engine and wait for more than 10 minutes.
8.
Check the oil level using the dipstick as shown. Add oil as nec-
essary and install the oil filler cap. Refer to
.
CAUTION:
Do not overfill the engine with oil.
Oil grade and viscosity
: Refer to
MA-16, "For North America: Fluids and
18, "For Mexico: Fluids and Lubricants"
co).
Oil capacity
: Refer to
.
PBIC2823E
LU-24
< ON-VEHICLE MAINTENANCE >
[VQ40DE]
OIL FILTER
OIL FILTER
Removal and Installation
INFOID:0000000005272531
REMOVAL
1.
Remove the engine front under cover. Refer to
EXT-13, "Removal and Installation"
.
2.
Drain engine oil. Refer to
3.
Remove the oil filter using Tool as shown.
WARNING:
Be careful not to burn yourself, as the engine and engine oil
may be hot.
CAUTION:
• Oil filter is equipped with a pressure relief valve.
• Use Genuine NISSAN Oil Filter or equivalent.
• When removing, prepare a shop cloth to absorb any
engine oil leaks or spills.
• Do not allow engine oil to adhere to drive belts.
• Completely wipe off any engine oil that adheres to the engine and the vehicle.
INSTALLATION
1.
Remove foreign materials adhering to the oil filter seal mating surface.
2.
Apply clean engine oil to the oil filter seal circumference of the
new oil filter as shown.
3.
Screw on the oil filter instructionly until it touches the installation
surface, then tighten it by 2/3 turn as shown. Or tighten to speci-
fication.
4.
Refill engine with new engine oil. Refer to
5.
Inspect the engine for oil leaks. Refer to
.
6.
Install the engine front under cover. Refer to
EXT-13, "Removal and Installation"
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
2.
Start the engine and check for engine oil leaks.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level and add engine oil as required.
Tool number
: KV10115801 (J-38956)
LBIA0425E
SMA010
Oil filter
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
SMA702C
OIL COOLER
LU-25
< ON-VEHICLE REPAIR >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
ON-VEHICLE REPAIR
OIL COOLER
Exploded View
INFOID:0000000005272532
Removal and Installation
INFOID:0000000005272533
WARNING:
Be careful not to burn yourself, as the engine oil and engine coolant may be hot.
CAUTION:
• Do not spill engine coolant on the drive belt.
• Do not spill engine oil on rubber parts such as drive belts and engine mounting insulator.
REMOVAL
NOTE:
When removing oil cooler only, step 1 is unnecessary.
1.
Drain engine coolant from radiator and cylinder block. Refer to
CO-39, "Changing Engine Coolant"
EM-215, "Disassembly and Assembly"
NOTE:
Perform this step only when removing water pipes and hoses.
2.
Remove engine front under cover. Refer to
EXT-13, "Removal and Installation"
3.
Disconnect water hoses from oil cooler, pinching hoses near oil cooler to prevent engine coolant from
spilling.
WBIA0572E
1.
Water connector
2.
Water hose
3.
Water pipe
4.
Oil pan (upper) front side
5.
O-ring
6.
Relief valve
7.
Oil cooler
8.
Oil filter
9.
Connector bolt
LU-26
< ON-VEHICLE REPAIR >
[VQ40DE]
OIL COOLER
CAUTION:
Perform this step when engine is cold.
4.
Remove oil filter. Refer to
LU-24, "Removal and Installation"
5.
Remove connector bolt, and remove oil cooler.
INSPECTION AFTER REMOVAL
Oil Cooler
Check oil cooler for cracks. Check oil cooler for clogging by blowing compressed air through engine coolant
inlet. If necessary, replace oil cooler assembly.
Relief Valve
Check relief valve for movement, cracks and breaks by pushing the ball. If replacement is necessary, remove
relief valve by prying it out using a suitable tool. Install a new relief valve in place by tapping it in.
INSTALLATION
Installation is in the reverse order of removal, paying attention to the following.
• Confirm that no foreign objects are adhering to the sealing sur-
faces of the oil cooler and oil pan (upper).
• Tighten connector bolt after aligning cutout on oil cooler with pro-
trusion on oil pan (upper) side.
INSPECTION AFTER INSTALLATION
1.
Check engine oil and engine coolant levels and add engine oil and engine coolant. Refer to
.
2.
Start the engine, and check for leaks of engine oil or engine coolant.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level and the engine coolant level again. Refer to
.
PBIC2825E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст