Nissan Frontier D40. Instruction — part 289
REAR PROPELLER SHAFT
DLN-177
< DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 3S1330-2BJ100]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4.
Make sure that the journal moves smoothly and is below the
joint flex effort specification. Refer to
.
Center Support Bearing
1.
Apply a thin coat of multi-purpose grease to both the propeller shaft tube and the inside surface of the
center support bearing.
2.
Install the center support bearing on the propeller shaft tube
using a suitable pipe pressing on the inner race.
3.
Install a new clamp over the boot on the slip yoke.
4.
Align the matching marks and install the slip yoke on the propeller shaft tube.
5.
Clean the surfaces and position the boot over the propeller shaft tube and tighten the clamp.
6.
Install the center support bearing bracket, then install the rear
propeller shaft assembly in the vehicle. Refer to
LDIA0119E
LDIA0153E
WDIA0066E
DLN-178
< SERVICE DATA AND SPECIFICATIONS (SDS)
[PROPELLER SHAFT: 3S1330-2BJ100]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000005275537
*Off-Road
Snap Ring
INFOID:0000000005275538
Model 3S1330–2B100
Unit: mm (in)
*Always check with the Parts Department for the latest parts information.
Applied model
Long bed 4WD
Short bed 2WD
VQ40DE
M/T
A/T
A/T
Propeller shaft model
3S1330–2BJ100
Number of joints
3
Coupling method with rear final drive
Flange type
Coupling method with transmission
Sleeve type
1st Shaft length (Center bearing to spider)
625.5
±
1.5 mm (24.63
±
0.06 in)
625.5
±
1.5 mm (24.63
±
0.06 in)
741.5
±
1.5 mm (29.19
±
0.06
in)
2nd Shaft length (CV joint to flange mount
surface)
783.6
±
1.5 mm (30.85
±
0.06 in)
813.6
±
1.5mm (32.03
±
0.06 in)
813.6
±
1.5mm (32.03
±
0.06
in) [783.6
±
1.5 mm (30.85
±
0.06 in)]*
Shaft outer diameter
76.2 +0.00/ - 0.13 mm (3.00 + 0.00/ - 0.01 in)
Journal axial play
0.02 mm (0.0008 in) or less
Propeller shaft runout limit
0.6 mm (0.024 in) or less
Propeller shaft joint flex effort
2.26 N·m (0.23 kg-m, 20 in-lb) or less
Thickness
Color
Part Number*
1.99 (0.0783)
White
37146-C9400
2.02 (0.0795)
Yellow
37147-C9400
2.05 (0.0807)
Red
37148-C9400
2.08 (0.0819)
Green
37149-C9400
2.11 (0.0831)
Blue
37150-C9400
2.14 (0.0843)
Light brown
37151-C9400
2.17 (0.0854)
Black
37152-C9400
2.20 (0.0866)
No paint
37153-C9400
PRECAUTIONS
DLN-179
< PRECAUTION >
[FRONT FINAL DRIVE: R180A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005590287
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Servicing Front Final Drive
INFOID:0000000005612410
• Before starting diagnosis of the vehicle, understand the symptoms well. Perform correct and systematic
operations.
• Check for the correct installation status prior to removal or disassembly. When matching marks are required,
be certain they do not interfere with the function of the parts they are applied to.
• Overhaul should be done in a clean work area, a dust proof area is recommended.
• Before disassembly, completely remove sand and mud from the exterior of the unit, preventing them from
entering into the unit during disassembly or assembly.
• Always use shop paper for cleaning the inside of components.
• Avoid using cotton gloves or a shop cloth to prevent the entering of lint.
• Check appearance of the disassembled parts for damage, deformation, and abnormal wear. Replace them
with new ones if necessary.
• Gaskets, seals and O-rings should be replaced any time the unit is disassembled.
• Clean and flush the parts sufficiently and blow them dry.
• Be careful not to damage sliding surfaces and mating surfaces.
• When applying sealant, remove the old sealant from the mating surface; then remove any moisture, oil, and
foreign materials from the application and mating surfaces.
• In principle, tighten nuts or bolts gradually in several steps working diagonally from inside to outside. If a
tightening sequence is specified, observe it.
• During assembly, observe the specified tightening torque.
• Add new differential gear oil, petroleum jelly, or multi-purpose grease, as specified.
DLN-180
< PREPARATION >
[FRONT FINAL DRIVE: R180A]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000005275540
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV381054S0
(J-34286)
Puller
Removing front oil seal
ST30720000
(J-25405)
Drift
• Installing front oil seal
• Installing side oil seal
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.
ST27863000
(
—
)
Drift
• Installing front oil seal
• Installing side oil seal
a: 74.5 mm (2.933 in) dia.
b: 62.5 mm (2.461 in) dia.
ST3127S000
(J-25765-A)
Preload gauge
1: GG91030000
(J-25765)
Torque wrench
2: HT62940000
(
—
)
Socket adapter (1/2
″
)
3: HT62900000
(
—
)
Socket adapter (3/8
″
)
Measuring drive pinion bearing preload torque
and total preload torque
KV10111100
(J-37228)
Seal cutter
Removing carrier cover
ZZA0601D
ZZA0811D
ZZA1003D
NT124
S-NT046
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст