Nissan Frontier D40. Instruction — part 288
REAR PROPELLER SHAFT
DLN-173
< REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 3S1330-2BJ100]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
REAR PROPELLER SHAFT
Removal and Installation
INFOID:0000000005275535
COMPONENTS
Model 3S1330–2BJ100
REMOVAL
1.
Put the transmission in neutral and release the parking brake.
2.
Put matching marks on the rear propeller shaft flange yoke and
the rear final drive companion flange as shown.
CAUTION:
For matching marks, use paint. Never damage the rear pro-
peller shaft flange yoke or the companion flange.
3.
Remove the bolts, then remove the propeller shaft from the rear
final drive and transmission or transfer.
INSPECTION
AWDIA0689GB
1.
Propeller shaft (1st shaft)
2.
Snap ring
3.
Journal bearing
4.
Sleeve yoke (4WD)
5.
Sleeve yoke (2WD)
6.
Journal
7.
Propeller shaft (2nd shaft)
Front
WDIA0049E
DLN-174
< REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 3S1330-2BJ100]
REAR PROPELLER SHAFT
• Inspect the propeller shaft runout. If runout exceeds the limit,
replace the propeller shaft assembly.
• While holding the flange yoke on one side, check axial play of the
joint as shown. If the journal axial play exceeds the specification,
repair or replace the journal parts.
• Check the propeller shaft for dents or cracks. If damage is
detected, replace the propeller shaft assembly.
INSTALLATION
Installation is in the reverse order of removal.
• After installation, check for vibration by driving the vehicle. Refer to
DLN-171, "NVH Troubleshooting Chart"
.
CAUTION:
Do not reuse the bolts and nuts. Always install new ones.
Propeller shaft runout limit
2WD
: Refer to
4WD
: Refer to
LDIA0121E
Journal axial play
: Refer to
LDIA0117E
REAR PROPELLER SHAFT
DLN-175
< DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 3S1330-2BJ100]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
DISASSEMBLY AND ASSEMBLY
REAR PROPELLER SHAFT
Disassembly and Assembly
INFOID:0000000005840686
DISASSEMBLY
Journal
1.
Remove the propeller shaft assembly from the vehicle. Refer to
DLN-173, "Removal and Installation"
.
2.
Put matching marks on the rear propeller shaft tube and flange
yoke as shown.
CAUTION:
For matching marks use paint. Never damage the rear pro-
peller shaft or flange yoke.
3.
Remove the snap rings.
4.
Push out and remove the journal bearing by lightly tapping the
yoke with a hammer, taking care not to damage the journal or
yoke hole.
5.
Remove the bearing at the opposite side of above operation.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
SPD128
APD011
SPD732
SPD131
DLN-176
< DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 3S1330-2BJ100]
REAR PROPELLER SHAFT
Center Support Bearing
1.
Remove the propeller shaft assembly from the vehicle. Refer to
DLN-173, "Removal and Installation"
2.
Put matching marks on the propeller shaft tube and the slip yoke.
CAUTION:
For matching marks, use paint. Never damage the propeller shaft tube or slip yoke.
3.
Remove and discard the clamp near the center support bearing, then slide the slip yoke off of propeller
shaft tube.
4.
Press the center support bearing off the propeller shaft tube
using Tool and suitable hydraulic press.
ASSEMBLY
Journal
1.
Assemble the journal bearings. Apply multipurpose grease on
the bearing inner surface.
NOTE:
During assembly, use caution so that the needle bearings do not
fall down.
2.
Select snap rings that will provide the specified play in an axial
direction of the journal, and install them. Refer to
.
NOTE:
Select snap rings with a difference in thickness at both sides
within 0.02 mm (0.0008 in).
3.
Adjust the thrust clearance between the bearing and snap ring
to zero by tapping the yoke.
Tool number
: 205-D002
LDIA0152E
WPD019
APD012
SPD732
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст