Nissan Frontier D40. Instruction — part 926
AXLE OIL SEAL
RAX-13
< SERVICE INFORMATION >
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
AXLE OIL SEAL
Removal and Installation
INFOID:0000000005275000
The axle oil seal must be replaced every time the axle shaft is removed and installed. Refer to
CAUTION:
Do not reuse the axle oil seal. The axle oil seal must be replaced every time the axle shaft assembly is
removed from the axle shaft housing.
RAX-14
< SERVICE INFORMATION >
[C200]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Axle Specification
INFOID:0000000005275001
Unit: mm (in)
Shim Washers
INFOID:0000000005275002
Unit: mm (in)
*: Always check with the Parts Department for the latest parts information.
Axial end play
0 - 0.07 (0 - 0.003)
Snap ring to shim washer clearance
0.2 (0.008) or less
Snap ring outer diameter installed
47.5 (1.87) maximum
Total end play
0.02 - 0.15 (0.0008 - 0.0059)
Available shim washers
ID Paint Dot Color
Thickness
Part Number*
Pink
2.5 (0.098)
43086-EB08C
Black
2.4 (0.094)
43086-EB07C
Purple
2.3 (0.091)
43086-EB06C
Yellow
2.2 (0.087)
43086-EB05C
Green
2.1 (0.083)
43086-EB04C
Red
2.0 (0.079)
43086-EB03C
White
1.9 (0.075)
43086-EB02C
Blue
1.8 (0.071)
43086-EB01C
PRECAUTIONS
RAX-15
< SERVICE INFORMATION >
[M226]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SERVICE INFORMATION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005549050
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution
INFOID:0000000005275003
• When installing rubber parts, final tightening must be carried out under unladen condition* with tires
on ground.
* Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated posi-
tions.
• After installing removed suspension parts, check wheel alignment and adjust if necessary.
RAX-16
< SERVICE INFORMATION >
[M226]
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000005275004
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000005275005
Tool number
(Kent-Moore No.)
Tool name
Description
205-D002
(
—
)
Bearing splitter
Removing axle shaft bearing
ZZA0700D
Tool name
Description
Power tools
Removing and installing nuts and bolts
PBIC0190E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст