Nissan Pathfinder (2006 year). Instruction — part 230
ROOF RACK
EI-23
C
D
E
F
G
H
J
K
L
M
A
B
EI
2006 Pathfinder
ROOF RACK
PFP:73155
Removal and Installation
EIS007U1
REMOVAL
1.
Pry outward releasing the clips and remove the slide rail cover front LH and RH.
2.
Pry outward releasing the clips and remove the slide rail cover rear LH and RH.
3.
Remove the bolts and remove front and rear sliding crossbars from slide rails.
4.
Remove the bolts from the slide rails LH and RH.
5.
Shift the slide rails forward to disengage from center stanchion and remove from roof.
6.
Remove the bolts and remove center stansions LH and RH from roof.
INSTALLATION
Installation is in the reverse order of removal.
1.
Slide rail
2.
Sliding crossbar
3.
Slide rail cover rear
4.
Center stanchion
5.
Slide rail cover front
LIIA1776E
EI-24
DOOR OUTSIDE MOLDING
2006 Pathfinder
DOOR OUTSIDE MOLDING
PFP:82820
Removal and Installation
EIS007U2
FRONT DOOR OUTSIDE MOLDING
Removal
1.
Open the window fully.
2.
Remove the door mirror. Refer to
.
3.
Lift molding from the front side off of flange.
4.
Remove the front door outside molding.
Installation
Installation is in the reverse order of removal.
LIIA1780E
DOOR FINISHER
EI-25
C
D
E
F
G
H
J
K
L
M
A
B
EI
2006 Pathfinder
DOOR FINISHER
PFP:80900
Removal and Installation
EIS007U3
FRONT DOOR
Removal
1.
Remove power window switch assembly.
●
Disconnect harness connectors.
2.
Remove pull handle escutcheon.
3.
Remove pull handle cover and remove screw.
4.
Lift armrest upward to release clips and remove armrest.
●
Remove screws behind armrest.
5.
Remove memory seat switch (if equipped).
●
Disconnect harness connector.
1.
Front door
2.
Mirror bolt cover LH
3.
Mirror bolt cover RH
4.
Pull handle escutcheon
5.
Pull handle/lock lever assembly
6.
Pull handle cover
7.
Front door finisher (RH shown)
8.
Seat memory switch (if equipped)
9.
Power window/lock switch assembly
10. Armrest
11.
Front door handle bracket
LIIA1782E
EI-26
DOOR FINISHER
2006 Pathfinder
6.
Release clips and remove door finisher.
●
Disconnect lock cable and handle cable from door handle assembly. Refer to
7.
Remove pull handle/lock lever assembly.
Installation
Installation is in the reverse order of removal.
REAR DOOR
Removal
1.
Remove power window switch assembly.
●
Disconnect harness connector.
2.
Remove pull handle cover.
●
Remove screw behind pull handle cover.
3.
Remove pull handle escutcheon.
4.
Lift upward to release clips and remove armrest.
●
Remove screws behind armrest.
5.
Release the clips and remove rear door finisher.
●
Disconnect the rear door tweeter.
Installation
Installation is in the reverse order of removal.
1.
Rear door
2.
Pull handle escutcheon
3.
Pull handle cover
4.
Metal clip
5.
Power window switch assembly
6.
Armrest
7.
Rear door finisher
8.
Rear door handle bracket
LIIA1785E
BODY SIDE TRIM
EI-27
C
D
E
F
G
H
J
K
L
M
A
B
EI
2006 Pathfinder
BODY SIDE TRIM
PFP:76913
Components
EIS007U4
CAUTION:
●
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from finishers.
●
When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finisher.
1.
Center pillar upper finisher
2.
Center pillar assist grip
3.
Rear door welt
4.
Rear kick plate
5.
Access cover (Passenger side only)
6.
Center pillar lower finisher
7.
Front kick plate
8.
Lower dash side finisher
9.
Clip
10. Front door welt
11.
Front pillar lower finisher
12.
Front pillar upper finisher
13. Front pillar assist grip
14.
RH side demister grille
15.
Molded plastic clip
16. Metal clip
17.
Garnish
LIIA1786E
EI-28
BODY SIDE TRIM
2006 Pathfinder
Removal and installation
EIS007U5
LOWER DASH SIDE FINISHER
Removal
1.
Remove push pin from lower dash side finisher.
2.
Remove front kick plate from center pillar lower finisher.
3.
Remove lower dash side finisher and front kick plate together.
4.
Remove lower dash side finisher from front kick plate.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR LOWER FINISHER
Removal
1.
Remove seat belt anchor. Refer to
SB-3, "Removal and Installation of Front Seat Belt"
●
On RH side, disconnect seat belt tension sensor.
2.
Remove front and rear kick plates. Refer to
.
3.
Remove center pillar lower finisher.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR UPPER FINISHER
Removal
1.
Remove front and rear door welts.
2.
Remove seat belt shoulder anchor and D-ring. Refer to
SB-3, "Removal and Installation of Front Seat
3.
Remove front and rear kick plates. Refer to
.
4.
Remove center pillar lower finisher.
5.
Remove assist grip.
6.
Remove center pillar upper finisher.
Installation
Installation is in the reverse order of removal.
FRONT PILLAR UPPER FINISHER
Removal
1.
Remove the front pillar assist grip.
2.
Remove the front pillar upper finisher bolt.
3.
Remove the front pillar upper finisher.
Installation
Installation is in the reverse order of removal.
FRONT PILLAR LOWER FINISHER
Removal
1.
Remove the lower dash side finisher. Refer to
EI-28, "LOWER DASH SIDE FINISHER"
2.
Remove the front pillar lower finisher.
Installation
Installation is in the reverse order of removal.
KICK PLATES
Removal
Release clips and remove front and/or rear kick plates.
Installation
Installation is in the reverse order of removal.
FLOOR TRIM
EI-29
C
D
E
F
G
H
J
K
L
M
A
B
EI
2006 Pathfinder
FLOOR TRIM
PFP:74902
Removal and Installation
EIS007U6
Front and Rear Floor Carpet
REMOVAL
Front Carpet
1.
Remove front seats. Refer to
2.
Remove lower seat belt anchors. Refer to
3.
Remove lower body side trim panels. Refer to
4.
Remove center console. Refer to
5.
Remove floor mat hook from front carpet.
6.
Remove front carpet.
Rear Carpet
1.
Remove 3rd row seats. Refer to
2.
Remove luggage side lower finisher RH and LH. Refer to
EI-34, "Removal and Installation"
.
3.
Remove flipper doors and floor tray. Refer to
EI-34, "Removal and Installation"
4.
Remove the bolts and the storage box. Refer to
EI-34, "Removal and Installation"
5.
Remove the rear carpet.
INSTALLATION
Installation is in the reverse order of removal.
LIIA1770E
1.
Front carpet
2.
Floor mat hook
3.
Clip
4.
Rear carpet
EI-30
HEADLINING
2006 Pathfinder
HEADLINING
PFP:73910
Removal and Installation
EIS007U7
REMOVAL
CAUTION:
Disconnect both the negative and positive battery terminals in advance.
1.
Disconnect the negative and positive battery terminals, then wait at least 3 minutes.
2.
Remove body side trim panels. Refer to
.
3.
Remove luggage floor trim upper panels. Refer to
4.
Remove sun visor assemblies, both LH and RH.
5.
Remove sun visor holders LH and RH.
1.
Sun visor holder LH/RH
2.
Sun visor assembly RH
3.
Front assist grip RH
4.
Rear assist grip LH
5.
Front roof console with front room
lamp assembly and sunglass bin
6.
Sunroof welt (if equipped)
7.
DVD video monitor finisher (if
equipped)
8.
Center room lamp assembly
9.
Rear room lamp assembly
10.
Clip
11.
Rear assist grip LH
12. Headlining
13.
Sun visor assembly LH
LIIA1778E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст