Nissan Pathfinder (2006 year). Instruction — part 311
AUTO LIGHT SYSTEM
LT-43
C
D
E
F
G
H
I
J
L
M
A
B
LT
2006 Pathfinder
Schematic
EKS00FV3
WKWA4305E
LT-44
AUTO LIGHT SYSTEM
2006 Pathfinder
Wiring Diagram — AUTO/L —
EKS00FV4
WKWA4226E
AUTO LIGHT SYSTEM
LT-45
C
D
E
F
G
H
I
J
L
M
A
B
LT
2006 Pathfinder
WKWA2028E
LT-46
AUTO LIGHT SYSTEM
2006 Pathfinder
WKWA4306E
AUTO LIGHT SYSTEM
LT-47
C
D
E
F
G
H
I
J
L
M
A
B
LT
2006 Pathfinder
Terminals and Reference Values for BCM
EKS00FV5
Refer to
BCS-12, "Terminals and Reference Values for BCM"
Terminals and Reference Values for IPDM E/R
EKS00FV6
Refer to
PG-28, "Terminals and Reference Values for IPDM E/R"
.
How to Proceed With Trouble Diagnosis
EKS00FV7
1.
Confirm the symptom or customer complaint.
2.
Understand operation description and function description. Refer to
.
3.
Carry out the Preliminary Check. Refer to
4.
Check symptom and repair or replace the cause of malfunction. Refer to
LT-53, "Trouble Diagnosis Chart
5.
Does the auto light system operate normally? If YES: GO TO 6. If NO: GO TO 4.
6.
Inspection End.
Preliminary Check
EKS00FV8
SETTING CHANGE FUNCTIONS
●
Sensitivity of auto light system can be adjusted using CONSULT-II or with display (with NAVI). Refer to
.
CHECK BCM CONFIGURATION
1.
CHECK BCM CONFIGURATION
Confirm BCM configuration for "AUTO LIGHT" is set to "WITH". Refer to
.
OK or NG
OK
>> Continue preliminary check. Refer to
LT-47, "CHECK POWER SUPPLY AND GROUND CIR-
.
NG
>> Change BCM configuration for "AUTO LIGHT" to "WITH". Refer to
.
CHECK POWER SUPPLY AND GROUND CIRCUIT
BCS-16, "BCM Power Supply and Ground Circuit Check"
and
PG-30, "IPDM E/R Power/Ground Cir-
.
CONSULT-II Function (BCM)
EKS00FV9
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
BCM diagnostic
test item
Diagnostic mode
Description
Inspection by part
WORK SUPPORT
Supports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR
Displays BCM input/output data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending drive signal to them.
SELF-DIAG RESULTS
Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER
BCM part number can be read.
CONFIGURATION
Performs BCM configuration read/write functions.
LT-48
AUTO LIGHT SYSTEM
2006 Pathfinder
1.
With the ignition switch OFF, connect CONSULT-II and CON-
SULT-II CONVERTER to the data link connector, then turn igni-
tion switch ON.
2.
Touch "START (NISSAN BASED VHCL)".
3.
Touch "BCM" on "SELECT SYSTEM" screen.
If "BCM" is not indicated, go to
4.
Touch "HEAD LAMP" on "SELECT TEST ITEM" screen.
WORK SUPPORT
Operation Procedure
1.
Touch "HEAD LAMP" on "SELECT TEST ITEM" screen.
2.
Touch "WORK SUPPORT" on "SELECT DIAG MODE" screen.
3.
Touch "CUSTOM A/LIGHT SETTING" or "ILL DELAY SET" on "SELECT WORK ITEM" screen.
4.
Touch "START".
5.
Touch "MODE 1-4" of setting to be changed (CUSTOM A/LIGHT SETTING). Touch "MODE1-8" of setting
to be changed (ILL DELAY SET).
6.
Touch "CHANGE SETT".
BBIA0538E
BCIA0029E
BCIA0030E
LKIA0183E
AUTO LIGHT SYSTEM
LT-49
C
D
E
F
G
H
I
J
L
M
A
B
LT
2006 Pathfinder
7.
The setting will be changed and "CUSTOMIZING COMPLETED" will be displayed.
8.
Touch "END".
Work Support Setting Item
●
Sensitivity of auto light can be selected and set from four modes.
DATA MONITOR
Operation Procedure
1.
Touch "HEAD LAMP" on "SELECT TEST ITEM" screen.
2.
Touch "DATA MONITOR" on "SELECT DIAG MODE" screen.
3.
Touch either "ALL SIGNALS" or "SELECTION FROM MENU" on the "SELECT MONITOR ITEM" screen.
4.
Touch "START".
5.
When "SELECTION FROM MENU" is selected, touch individual items to be monitored. When "ALL SIG-
NALS" is selected, all the items will be monitored.
6.
Touch "RECORD" while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch "STOP".
Display Item List
Work item
Description
CUSTOM A/LIGHT SETTING
Auto light sensitivity can be changed in this mode. Sensitivity can be adjusted in four modes.
●
MODE 1 (Normal-default)/ MODE 2 (Desensitized)/MODE 3 (Sensitive)/MODE4 (Insensitive)
ILL DELAY SET
Auto light delay off timer period can be changed in this mode. Selects auto light delay off timer
period among eight modes.
●
MODE 1 (45 sec.)/MODE 2 (OFF)/MODE 3 (30 sec.)/MODE 4 (60 sec.)/MODE 5 (90 sec.)/
MODE 6 (120 sec.)/MODE 7 (150 sec.)/MODE 8 (180 sec.)
ALL SIGNALS
Monitors all the signals.
SELECTION FROM MENU
Selects and monitors individual signal.
Monitor item
Contents
IGN ON SW
"ON/OFF"
Displays "IGN position (ON)/OFF, ACC position (OFF)" judged from the ignition switch
signal.
ACC ON SW
"ON/OFF"
Displays "ACC (ON)/OFF, Ignition OFF (OFF)" status judged from ignition switch signal.
HI BEAM SW
"ON/OFF"
Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from
lighting switch signal.
HEAD LAMP SW 1
"ON/OFF"
Displays status (headlamp switch 1: ON/Others: OFF) of headlamp switch 2 judged from
lighting switch signal.
HEAD LAMP SW 2
"ON/OFF"
Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from
lighting switch signal.
LIGHT SW 1ST
"ON/OFF"
Displays status (lighting switch 1st position: ON/Others: OFF) of lighting switch judged
from lighting switch signal.
AUTO LIGHT SW
"ON/OFF"
Displays status of the lighting switch as judged from the lighting switch signal. (AUTO
position: ON/Other than AUTO position: OFF)
PASSING SW
"ON/OFF"
Displays status (flash-to-pass switch: ON/Others: OFF) of flash-to-pass switch judged
from lighting switch signal.
FR FOG SW
"ON/OFF"
Displays status (front fog lamp switch: ON/Others: OFF) of front fog lamp switch judged
from lighting switch signal.
DOOR SW-DR
"ON/OFF"
Displays status of the front door LH as judged from the front door switch LH signal. (Door
is open: ON/Door is closed: OFF)
DOOR SW-AS
"ON/OFF"
Displays status of the front door RH as judged from the front door switch RH signal. (Door
is open: ON/Door is closed: OFF)
DOOR SW-RR
"ON/OFF"
Displays status of the rear door as judged from the rear door switch (RH) signal. (Door is
open: ON/Door is closed: OFF)
DOOR SW-RL
"ON/OFF"
Displays status of the rear door as judged from the rear door switch (LH) signal. (Door is
open: ON/Door is closed: OFF)
LT-50
AUTO LIGHT SYSTEM
2006 Pathfinder
ACTIVE TEST
Operation Procedure
1.
Touch "HEAD LAMP" on "SELECT TEST ITEM" screen.
2.
Touch "ACTIVE TEST" on "SELECT DIAG MODE" screen.
3.
Touch item to be tested and check operation of the selected item.
4.
During the operation check, touching "BACK" deactivates the operation.
Display Item List
BACK DOOR SW
"ON/OFF"
Displays status of the back door as judged from the back door switch signal. (Door is
open: ON/Door is closed: OFF)
TURN SIGNAL R
"ON/OFF"
Displays status (Turn right: ON/Others: OFF) as judged from lighting switch signal.
TURN SIGNAL L
"ON/OFF"
Displays status (Turn left: ON/Others: OFF) as judged from lighting switch signal.
CARGO LAMP SW
"ON/OFF"
Displays status of cargo lamp.
OPTICAL SENSOR
[0 - 5V]
Displays "ambient light (close to 5V when dark/close to 0V when light)" judged from opti-
cal sensor signal.
Monitor item
Contents
Test item
Description
TAIL LAMP
Allows tail lamp relay to operate by switching ON-OFF.
HEAD LAMP
Allows headlamp relay (HI, LO) to operate by switching ON-OFF.
FR FOG LAMP
Allows fog lamp relay to operate by switching ON-OFF.
CARGO LAMP
Allows cargo lamp to operate by switching ON-OFF.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст