Nissan Pathfinder (2006 year). Instruction — part 35
DISASSEMBLY
AT-271
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
35. Remove bolts A, B and C from control valve with TCM.
36. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the instruction valve notch and
instruction plate height. Remove it vertically.
37. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
38. Remove bracket from A/T fluid temperature sensor 2.
39. Remove O-ring from A/T assembly harness connector.
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA5025E
SCIA5260E
SCIA5301E
SCIA5264E
SCIA5155E
AT-272
DISASSEMBLY
2006 Pathfinder
40. Disconnect TCM connectors.
CAUTION:
Be careful not to damage connectors.
41. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
42. Disconnect TCM connector and park/neutral position switch
connector.
CAUTION:
Be careful not to damage connectors.
43. Remove rear extension assembly (2WD models) or adapter case assembly (4WD models) according to
the following procedures.
a.
2WD models
i.
Remove bolts for rear extension assembly and transmission
case.
SCIA5447E
SCIA5448E
SCIA5449E
SCIA6941E
DISASSEMBLY
AT-273
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
ii.
Tap rear extension assembly with soft hammer.
iii.
Remove rear extension assembly from transmission case. (With
needle bearing.)
b.
4WD models
i.
Remove bolts (1) for adapter case assembly and transmission
case. (With terminal bracket (2).)
●
Self-sealing bolt (3)
ii.
Tap adapter case assembly with soft hammer.
SCIA5028E
SCIA5029E
SCIA7220E
SCIA5201E
AT-274
DISASSEMBLY
2006 Pathfinder
iii.
Remove adapter case assembly from transmission case. (With
needle bearing)
iv.
Remove gasket from transmission case.
44. Remove bearing race from output shaft.
45. Remove output shaft from transmission case by rotating left/
right.
46. Remove parking gear from output shaft.
SCIA5186E
SCIA5231E
SCIA5245E
SCIA5030E
SCIA5247E
DISASSEMBLY
AT-275
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
47. Remove seal rings from output shaft.
48. Remove needle bearing from transmission case.
49. Remove revolution sensor from transmission case.
CAUTION:
●
Do not subject it to impact by dropping or hitting it.
●
Do not disassemble.
●
Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
●
Do not place in an area affected by magnetism.
50. Remove reverse brake snap ring using 2 flat-bladed screwdriv-
ers.
NOTE:
Press out snap ring from the transmission case oil pan side gap
using a flat-bladed screwdriver, and remove it using a another
screwdriver.
51. Remove reverse brake retaining plate from transmission case.
●
Check facing for burns, cracks or damage. If necessary,
replace the plate.
52. Remove N-spring from transmission case.
SCIA5209E
SCIA5031E
SCIA2320E
SCIA5032E
SCIA5214E
AT-276
DISASSEMBLY
2006 Pathfinder
53. Remove reverse brake drive plates, driven plates and dish plate
from transmission case.
●
Check facing for burns, cracks or damage. If necessary,
replace the plate.
54. Remove snap ring using suitable tool.
55. Remove spring retainer and return spring from transmission
case.
56. Remove seal rings from drum support.
57. Remove needle bearing from drum support edge surface.
SCIA2322E
SCIA2323E
SCIA2324E
SCIA3333E
SCIA2796E
DISASSEMBLY
AT-277
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
58. Remove reverse brake piston from transmission case with com-
CAUTION:
Care should be taken not to abruptly blow air. It makes pis-
tons incline, as the result, it becomes hard to disassemble
the pistons.
59. Remove D-rings from reverse brake piston.
60. Use a pin punch (4mm dia. commercial service tool) to knock
out retaining pin.
61. Remove instruction shaft retaining pin with a pair of nippers.
SCIA5047E
SCIA6330E
SCIA2328E
SCIA2329E
AT-278
DISASSEMBLY
2006 Pathfinder
62. Remove instruction plate (with parking rod) from instruction shaft.
63. Remove parking rod from instruction plate.
64. Remove instruction shaft from transmission case.
65. Remove instruction shaft oil seals using suitable tool.
CAUTION:
Be careful not to scratch transmission case.
66. Remove detent spring and spacer from transmission case.
SCIA5715E
SCIA5220E
SCIA5716E
SCIA2331E
SCIA5248E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст