Nissan Versa Note. Instruction — part 591
MWI
B2205 VEHICLE SPEED
MWI-39
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B2205 VEHICLE SPEED
Description
INFOID:0000000009654114
The ABS actuator and electric unit (control unit) provides a vehicle speed signal to the combination meter via
CAN communication lines.
DTC Logic
INFOID:0000000009654115
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009654116
1.
CHECK COMBINATION METER INPUT SIGNAL
1. Start engine and select METER/M&A on CONSULT.
2. Using SPEED METER on DATA MONITOR, compare the value of DATA MONITOR with speedometer
pointer of combination meter. Speedometer and DATA MONITOR indications should be close.
Is the inspection result normal?
YES
>> Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
.
NO
>> Replace combination meter. Refer to
MWI-54, "Removal and Installation"
DTC
Display Item
Malfunction detected condition
Possible malfunction
B2205
VEHICLE SPEED CIRC
[B2205]
Malfunction is detected when an erroneous
speed signal is received for 2 seconds or more.
• Combination meter
• ABS actuator and electric unit (control unit)
MWI-40
< DTC/CIRCUIT DIAGNOSIS >
B2267 ENGINE SPEED
B2267 ENGINE SPEED
Description
INFOID:0000000009654117
The engine speed signal is transmitted from ECM to the combination meter via CAN communication.
DTC Logic
INFOID:0000000009654118
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009654119
1.
PERFORM SELF-DIAGNOSIS OF ECM
Perform Self Diagnostic Result of ECM, and repair or replace malfunctioning parts.
>> Refer to
DTC
Display Item
Malfunction detected condition
Possible malfunction
B2267
TACHO METER
[B2267]
ECM continuously transmits abnormal engine
speed signals for 2 seconds or more
• Crankshaft position sensor (POS)
• ECM
MWI
B2268 WATER TEMP
MWI-41
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B2268 WATER TEMP
Description
INFOID:0000000009654120
The engine coolant temperature signal is transmitted from ECM to the combination meter via CAN communi-
cation.
DTC Logic
INFOID:0000000009654121
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009654122
1.
PERFORM SELF-DIAGNOSIS OF ECM
Perform Self Diagnostic Result of ECM, and repair or replace malfunctioning parts.
>> Refer to
.
DTC
Display Item
Malfunction detected condition
Possible malfunction
B2268
WATER TEMP METER
[B2268]
ECM continuously transmits abnormal engine coolant
temperature signals for 60 seconds or more
• Engine coolant temperature sensor
• ECM
MWI-42
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER
COMBINATION METER : Diagnosis Procedure
INFOID:0000000009654123
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSE
Check that the following fuses are not blown.
Is the fuse blown?
YES
>> GO TO 2.
NO
>> Replace the blown fuse after repairing the affected circuit.
2.
POWER SUPPLY CIRCUIT CHECK
1. Disconnect combination meter connector.
2. Check voltage between combination meter harness connector M24, terminals 27, 28, 15 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connector.
3.
GROUND CIRCUIT CHECK
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector M24, terminals 21, 22, 23 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connector.
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis
Power source
Fuse No.
Battery
8
Ignition switch ON or START
3
Ignition switch ACC or ON
18
Terminals
Ignition switch position
(+)
(–)
OFF
ACC
ON
START
Connector
Terminal
M24
27
Ground
Battery voltage
Battery voltage
Battery voltage
Battery voltage
28
0V
0V
Battery voltage
Battery voltage
15
0V
Battery voltage
Battery voltage
0V
Terminals
Continuity
(+)
(–)
Connector
Terminal
M24
21
Ground
Yes
22
23
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст