Nissan Versa Note. Instruction — part 883
REAR WIPER MOTOR CIRCUIT
WW-51
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
3.
CHECK REAR WIPER MOTOR OPEN CIRCUIT
Check continuity between BCM harness connector and rear wiper motor harness connector.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK REAR WIPER MOTOR SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> Repair or replace harness.
NO
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
BCM
Rear wiper motor
Continuity
Connector
Terminal
Connector
Terminal
M100
54
D502
2
Yes
BCM
Rear wiper motor
Continuity
Connector
Terminal
Connector
Terminal
M20
68
D502
2
Yes
BCM
Ground
Continuity
Connector
Terminal
M100
54
No
BCM
Ground
Continuity
Connector
Terminal
M20
68
No
WW-52
< DTC/CIRCUIT DIAGNOSIS >
REAR WIPER AUTO STOP SIGNAL CIRCUIT
REAR WIPER AUTO STOP SIGNAL CIRCUIT
Component Function Check
INFOID:0000000009643037
1.
CHECK REAR WIPER (AUTO STOP) OPERATION
CONSULT DATA MONITOR
1. Select WIPER of BCM data monitor item.
2. Operate the rear wiper.
3. Check that RR WIPER STOP changes to ON and OFF linked with the wiper operation.
Is the inspection result normal?
YES
>> Rear wiper auto stop signal circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009643038
Regarding Wiring Diagram information, refer to
.
1.
CHECK REAR WIPER MOTOR AUTO STOP CIRCUITS FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect BCM and rear wiper motor.
3. Check continuity between BCM harness connector terminal and rear wiper motor harness connector ter-
minal.
With Intelligent Key
Without Intelligent Key
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK AUTO STOP CIRCUITS FOR SHORT TO GROUND
Check continuity between BCM harness connector terminal and ground.
With Intelligent Key
Without Intelligent Key
Monitor item
Condition
Monitor status
RR WIPER STOP
Rear wiper motor
Stop position
ON
Except stop position
OFF
BCM
Rear wiper motor
Continuity
Connector
Terminal
Connector
Terminal
M100
44
D502
3
Yes
BCM
Rear wiper motor
Continuity
Connector
Terminal
Connector
Terminal
M20
56
D502
3
Yes
BCM
Ground
Continuity
Connector
Terminal
M100
44
No
BCM
Ground
Continuity
Connector
Terminal
M20
56
No
REAR WIPER AUTO STOP SIGNAL CIRCUIT
WW-53
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Is inspection result normal?
YES
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
(with Intelligent Key) or
(with Intelligent Key).
NO
>> Repair or replace harness.
WW-54
< SYMPTOM DIAGNOSIS >
WIPER AND WASHER SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
WIPER AND WASHER SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000009643039
CAUTION:
Perform the self-diagnosis with CONSULT before performing the diagnosis by symptom. Perform the
diagnosis by DTC if DTC is detected.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст