Nissan Versa Note. Instruction — part 663
REAR SUSPENSION BEAM
RSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION BEAM
Exploded View
INFOID:0000000009499809
Removal and Installation
INFOID:0000000009499810
NOTE:
When removing components such as hoses, tubes, lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the rear wheels and tires using power tools. Refer to
WT-45, "Removal and Installation"
2. Disconnect the brake hoses from the rear suspension beam.
3. Remove the spindles and rear drum brake components. Refer to
.
4. Remove the wheel sensors and position the wheel sensor harnesses aside. Refer to
WHEEL SENSOR : Removal and Installation"
5. Disconnect the parking brake cables from the rear suspension beam and position the rear drum brake
back plates aside with wire. Refer to
.
6. Set a suitable jack under the rear suspension beam.
CAUTION:
• At this step, the jack must be set only for supporting the removal procedure. For details on jack-
ing up the vehicle, refer to
GI-28, "Garage Jack and Safety Stand"
• Do not damage the rear suspension beam with the jack.
7. Remove the lower shock absorber bolts. Refer to
8. Slowly lower the suitable jack. Remove the upper rubber seats, the coil springs, and the lower rubber
seats from the rear suspension beam.
CAUTION:
Make sure the rear suspension beam is stable when using the jack.
9. Remove the rear suspension beam bolts.
10. Slowly lower the suitable jack. Remove the rear suspension beam from the vehicle.
11. Inspect the components. Refer to
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the rear suspension beam nuts.
1.
Rear suspension beam
AWEIA0323ZZ
RSU-14
< REMOVAL AND INSTALLATION >
REAR SUSPENSION BEAM
• Perform the final tightening of the rear suspension beam nuts and bolts under unladen conditions with the
tires on level ground.
• Adjust the parking brake. Refer to
PB-4, "Inspection and Adjustment"
• Fill the hydraulic brake system. Refer to
.
• Bleed the hydraulic brake system. Refer to
BR-12, "Bleeding Brake System"
• Complete the inspection. Refer to
.
Inspection
INFOID:0000000009499811
INSPECTION AFTER REMOVAL
Check the rear suspension beam for deformation, cracks or damage. Replace the parts if necessary.
INSPECTION AFTER INSTALLATION
1. Check the wheel sensor harness to be sure the connectors are fully seated.
2. Check the neutral position of the steering angle sensor. Refer to
3. Check the wheel alignment. Refer to
.
SERVICE DATA AND SPECIFICATIONS (SDS)
RSU-15
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment (Unladen*
1
)
INFOID:0000000009499812
*1: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
*2: Since an adjustment mechanism is not included, the value of the left and right wheels must be used as the standard value.
Wheelarch Height (Unladen*)
INFOID:0000000009499813
Unit: mm (in)
*: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
Camber
Degree minute (Decimal degree)
Minimum
−1° 55′ (−1.92°)
Nominal
−1° 25′ (−1.42°)
Maximum
−0° 55′ (−0.92°)
Total toe-in
Distance (A - B)
Minimum
Out 2.0 mm (Out 0.079 in)
Nominal
In 2.0 mm (In 0.079 in)
Maximum
In 6.0 mm (In 0.236 in)
Angle (LH and RH)
*2
Degree minute (Decimal degree)
Minimum
Out 0
° 45′ (Out 0.75°)
Nominal
In 0
° 10′ (In 0.17°)
Maximum
In 0
° 35′ (In 0.58°)
SFA234AC
Tire size
185/65R15
195/55R16
Front (Hf)
690 (27.17)
687 (27.05)
Rear (Hr)
679 (26.73)
678 (26.69)
LEIA0085E
SB-1
RESTRAINTS
C
D
E
F
G
I
J
K
L
M
SECTION
SB
A
B
SB
N
O
P
CONTENTS
SEAT BELT
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Seat Belt Service . . . . . . . ...
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
BASIC INSPECTION . . . . . . . . .
COMPONENT INSPECTION . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
FRONT SEAT BELT . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
FRONT SEAT BELT BUCKLE . . . . . . . . ....
FRONT SEAT BELT BUCKLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ....
SEAT BELT RETRACTOR . . . . . . . . . . .
SEAT BELT RETRACTOR : Removal and Instal-
lation . . . . . . . . . . . . . . . . . . .
SEAT BELT HEIGHT ADJUSTER . . . . . . . .
SEAT BELT HEIGHT ADJUSTER : Removal and
Installation . . . . . . . . . . . . . . . ...
REAR SEAT BELT . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
REAR SEAT BELT BUCKLE . . . . . . . . .
REAR SEAT BELT BUCKLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
SEAT BELT RETRACTOR . . . . . . . . . .
SEAT BELT RETRACTOR : Removal and Instal-
lation . . . . . . . . . . . . . . . . . .
LATCH (LOWER ANCHORS AND TETHER
FOR CHILDREN) SYSTEM . . . . . . . ...
Removal and Installation . . . . . . . . . . .
TOP TETHER STRAP CHILD RESTRAINT . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст