Nissan Versa Note. Instruction — part 662
REAR SHOCK ABSORBER
RSU-9
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
• To install the bushings (1), securely insert the protrusion (A) into
the hole in the vehicle body.
• Install the washer (1) in the direction shown.
• Perform the final tightening of the bolts and nuts under unladen conditions with the tires on level ground.
• Hold the tip (A) of the piston rod. Tighten the piston rod lock nut (1)
to the specification.
CAUTION:
Do not reuse the piston rod lock nut.
• When installing the cap, securely engage the cap groove (A) with
the flange on the vehicle body.
• After replacing the shock absorber, always follow the disposal procedure to discard the old shock absorber.
.
Inspection
INFOID:0000000009499804
INSPECTION AFTER REMOVAL
JPEIB0240ZZ
: Bushing side
JPEIB0248ZZ
JPEIB0241ZZ
JPEIB0244ZZ
RSU-10
< REMOVAL AND INSTALLATION >
REAR SHOCK ABSORBER
Shock Absorber
Check the following items and replace the parts if necessary.
• Check the shock absorber for oil leaks, deformation, cracks, and other damage.
• Check the piston rod for damage, uneven wear, and distortion.
Bound Bumper, Bushing
Check for cracks and damage. Replace the parts if necessary.
Washer, Bound Bumper Cover, Distance Tube
• Check for cracks and damage. Replace the parts if necessary.
Disposal
INFOID:0000000009499805
1. Set the shock absorber horizontally with the piston rod fully extended.
2. Drill a 2 – 3 mm (0.08 – 0.12 in) hole at the position ( ) from the
top as shown to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction (
).
• Drill directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3. Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
(A)
: 20 – 30 mm (0.79 – 1.18 in)
JPEIA0161ZZ
COIL SPRING
RSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
COIL SPRING
Exploded View
INFOID:0000000009499806
Removal and Installation
INFOID:0000000009499807
REMOVAL
1. Set a suitable jack under the rear suspension beam.
CAUTION:
• At this step, the jack must be set only for supporting the removal procedure. For details on jack-
ing up the vehicle, refer to
GI-28, "Garage Jack and Safety Stand"
• Do not damage the rear suspension beam with the jack.
2. Remove the lower shock absorber bolts. Refer to
3. Slowly lower the suitable jack. Remove the upper rubber seat, the coil spring, and the lower rubber seat
from the rear suspension beam.
CAUTION:
Make sure the rear suspension beam is stable when using the jack.
4. Inspect the components. Refer to
INSTALLATION
Installation is in the reverse order of removal.
• Identify the upper side of the coil spring.
NOTE:
The top of the coil spring has a flat shape.
1.
Upper rubber seat
2.
Coil spring
3.
Lower rubber seat
4.
Rear suspension beam
JPEIB0162ZZ
: Upper side
JSEIA0430ZZ
RSU-12
< REMOVAL AND INSTALLATION >
COIL SPRING
• Install the lower rubber seat (A) to the rear suspension beam
mounting hole (B).
• Match up lower rubber seat indentions and rear suspension beam
grooves and attach.
Inspection
INFOID:0000000009499808
INSPECTION AFTER REMOVAL
Check the upper rubber seat, the lower rubber seat, and the coil spring for deformation, cracks, and damage.
Replace the parts if necessary.
JPEIB0223ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст