Nissan Versa Note. Instruction — part 340
EC-342
< DTC/CIRCUIT DIAGNOSIS >
[HR16DE]
P059F ACTIVE GRILLE SHUTTER
With CONSULT
1. Start the engine and let it idle for 5 seconds or more.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> GO TO 3.
3.
DTC CONFIRMATION PROCEDURE A AND D
With CONSULT
1. Turn ignition switch OFF and wait 10 seconds or more.
2. Turn ignition switch ON.
3. Select “DATA MONITOR” mode of “ENGINE” using CONSULT.
4. Start the engine if the following conditions are met.
5. Select “ACTIVE GRILLE SHUTTER” in “ACTIVE TEST”of “ENGINE” using CONSULT.
6. Touch “CALIBRTN”at least 60 seconds.
7. Check 1st trip DTC.
Is 1st trip DTC is detected?
YES
>> Proceed to
.
NO
>> GO TO 4.
4.
DTC CONFIRMATION PROCEDURE C
With CONSULT
1. Drive 10 minutes or more under the status that following conditions are met.
CAUTION:
Always drive at a safe speed.
NOTE:
Maintain the conditions for 10 minutes or more for accumulation.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
5.
DTC CONFIRMATION PROCEDURE A, B AND D
1. Start the engine when the following conditions are met.
2. Drive the vehicle at 10 km/h (7 MPH) or more for at least 60 seconds.
3. Check DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> GO TO 6.
6.
DTC CONFIRMATION PROCEDURE C
1. Drive the vehicle for 10 minutes or more with the following conditions.
INT/A TEMP SE
0
°C (32°F) or more
COOLANT TEMP/S
0
°C (32°F) or more
VHCL SPEED SE
40 km/h (25 MPH) or more
INT/A TEMP SE
50
°C (122°F) or less
Intake air temperature
0
°C (32°F) or more
Engine coolant temperature 0
°C (32°F) or more
Vehicle speed
40 km/h (25 MPH) or more
Intake air temperature
50
°C (122°F) or less
P059F ACTIVE GRILLE SHUTTER
EC-343
< DTC/CIRCUIT DIAGNOSIS >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
CAUTION:
Always drive at a safe speed.
NOTE:
Maintain the conditions for 10 minutes or more for accumulation.
2. Check DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009509490
1.
CHECK ACTIVE GRILL SHUTTER
1. Turn ignition switch OFF.
2. Check if any foreign objects interferes with active grille shutter.
3. Check the installation condition of active grille shutter.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the error-detected parts.
2.
CHECK ACTIVE GRILLE SHUTTER POWER SUPPLY
1. Disconnect active grille shutter harness connector.
2. Check the voltage between active grille shutter harness connector and ground as follows.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 6.
3.
CHECK ACTIVE GRILLE SHUTTER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check the continuity between active grille shutter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the error-detected parts.
4.
CHECK ACTIVE GRILLE SHUTTER SIGNAL CIRCUIT
1. Disconnect ECM harness connector.
2. Check the continuity between ECM harness connector and active grille shutter harness connector.
+
−
Condition
Voltage
(Approx.)
Active grille shutter
Connector
Terminal
E303
4
Ground
Ignition switch: ON
Battery volt-
age
Ignition switch: OFF
0 V
+
−
Continuity
Active grille shutter
Connector
Terminal
E303
1
Ground
Existed
+
−
Continuity
ECM
Active grille shutter
Connector
Terminal
Connector
Terminal
F11
70
E303
2
Existed
EC-344
< DTC/CIRCUIT DIAGNOSIS >
[HR16DE]
P059F ACTIVE GRILLE SHUTTER
3. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the error-detected parts.
5.
CHECK ACTIVE GRILLE SHUTTER
Check active grille shutter. Refer to
EC-345, "Component Inspection (Active Grille Shutter)"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace active grille shutter. Refer to
EXT-31, "Removal and Installation"
.
6.
CHECK ACTIVE GRILLE SHUTTER POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Remove active grille shutter relay.
3. Check the continuity between active grille shutter harness connector and active grille shutter relay har-
ness connector.
4. Also check harness for short to ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace the error-detected parts.
7.
CHECK ACTIVE GRILLE SHUTTER RELAY POWER SUPPLY CIRCUIT - 1
Check the voltage between active grille shutter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 11.
8.
CHECK ACTIVE GRILLE SHUTTER RELAY SIGNAL CIRCUIT - 1
1. Check the voltage between active grille shutter harness connector and ground as follows.
2. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 12.
9.
CHECK ACTIVE GRILLE SHUTTER RELAY GROUND CIRCUIT
1. Turn ignition switch OFF
+
−
Continuity
Active grille shutter
Active grille shutter relay
Connector
Terminal
Connector
Terminal
E303
4
E72
3
Existed
+
−
Voltage
(Approx.)
Active grille shutter relay
Connector
Terminal
E72
5
Ground
Battery voltage
+
−
Condition
Voltage
(Approx.)
Active grille shutter relay
Connector
Terminal
E72
2
Ground
Ignition switch: ON
Battery volt-
age
Ignition switch: OFF
0 V
P059F ACTIVE GRILLE SHUTTER
EC-345
< DTC/CIRCUIT DIAGNOSIS >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2. Check the continuity between active grille shutter relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace the error-detected parts.
10.
CHECK ACTIVE GRILLE SHUTTER RELAY
Check active grille shutter relay. Refer to
EC-346, "Component Inspection (Active Grille Shutter Relay)"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace active grille shutter relay.
11.
CHECK ACTIVE GRILLE SHUTTER RELAY POWER SUPPLY CIRCUIT - 2
1. Check 5A fuse (No. 27).
2. Check the continuity between active grille shutter relay harness connector and fuse socket.
3. Also check harness for short to ground.
Is the inspection result normal?
YES
>> Perform trouble diagnosis for power supply circuit.
NO
>> Repair or replace the error-detected parts.
12.
CHECK ACTIVE GRILLE SHUTTER RELAY SIGNAL CIRCUIT - 2
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Check the continuity between active grille shutter relay harness connector and IPDM E/R harness con-
nector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> Perform trouble diagnosis for power supply circuit.
NO
>> Repair or replace the error-detected parts.
Component Inspection (Active Grille Shutter)
INFOID:0000000009509491
1.
CHECK ACTIVE GRILLE SHUTTER
With CONSULT
1. Start the engine.
2. Select “ACTIVE GRILLE SHUTTER” in “ACTIVE TEST” mode of “ENGINE” using CONSULT.
3. Touch “CALIBRTN”.
4. After the calibration completes, check the operation of active grille shutter as follows.
+
−
Continuity
Active grille shutter relay
Connector
Terminal
E72
1
Ground
Existed
+
Fuse No.
Continuity
Active grille shutter relay
Connector
Terminal
E72
5
27
Existed
+
−
Continuity
Active grille shutter relay
IPDM E/R
Connector
Terminal
Connector
Terminal
E72
2
F42
39
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст