Nissan Versa Note. Instruction — part 527
REAR DOOR FINISHER
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3. Remove screw (B) from power window and door lock/unlock
switch (RH) finisher.
4. Remove power window and door lock/unlock switch (RH) fin-
isher (1) using a suitable tool (A).
: Pawl
5. Disconnect the harness connector from the power window and door lock/unlock switch (RH).
6. Remove rear door finisher bolt (A).
7. Release rear door finisher clips using a suitable tool (A) and remove rear door finisher as shown.
: Clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation.
• When installing rear door finisher, check that clips and pawls are securely placed into door panel
holes.
REMOVAL - MANUAL WINDOW
1. Release rear door corner finisher clip using a suitable tool.
2. Release storage tray pawls using a suitable tool and remove storage tray .
AWJIA1140ZZ
JMJIA6028ZZ
INT-20
< REMOVAL AND INSTALLATION >
REAR DOOR FINISHER
3. Release the metal clip (A) behind the instruction window crank han-
dle using a suitable tool (B). Pull the instruction window crank han-
dle (1) outward from the front door finisher and remove handle.
4. Remove rear door finisher bolt (A).
5. Release rear door finisher clips using a suitable tool (A) and
remove rear door finisher as shown.
: Clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation.
• When installing rear door finisher, check that clips and pawls are securely placed into door panel
holes.
AWJIA1119ZZ
JMJIA6028ZZ
AWJIA1121ZZ
BODY SIDE TRIM
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000008969703
FRONT PILLAR FINISHER
FRONT PILLAR FINISHER : Removal and Installation
INFOID:0000000008969704
REMOVAL
1. Remove front pillar portion of front body side welt.
1. Center pillar upper finisher (RH)
2. Front body side welt (RH)
3. Front pillar finisher (RH)
4. Dash side finisher (RH)
5. Front kicking plate (RH)
6. Center pillar lower finisher (RH)
7. Rear kicking plate (RH)
8. Rear body side welt (RH)
Front
Clip
Pawl
AWJIA1141ZZ
INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2. Pull front pillar finisher downward as shown to release the front
pillar finisher clip (bottom).
: Clip
: Pawl
3. Cut and discard front pillar finisher tether clips.
4. Remove the remaining piece of the tether clip (B) using a suit-
able tool (A).
INSTALLATION
1. Install new front pillar finisher tether clips (A) to the front pillar
finisher by inserting clip end and rotating 90 degrees to fit.
CAUTION:
• Do not reuse tether clips. Replace with new part after
removal.
• Make sure to install tether clip to front pillar finisher
before installing front pillar finisher.
• When installing tether clip to front pillar finisher, be sure
to install by aligning to the cutout.
• Visually check the clip for deformation and damage dur-
ing installation. Replace with new one if necessary.
• When installing front pillar finisher, check that clip and
tether clips are securely placed into body panel holes.
2. Install the front pillar finisher to the front pillar.
KICKING PLATE
KICKING PLATE : Removal and Installation
INFOID:0000000008969706
FRONT KICKING PLATE
Removal
AWJIA1124ZZ
AWJIA1111ZZ
AWJIA1088ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст