Nissan Versa Note. Instruction — part 528
BODY SIDE TRIM
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
1. Release front kicking plate pawls and metal clip using a suitable
tool (A) and remove front kicking plate as shown.
: Pawl
: Metal clip
Installation
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation.
• When installing front kicking plate, check that clips and pawls are securely placed into body panel
holes.
REAR KICKING PLATE
Removal
1. Remove rear seat cushion. Refer to
2. Lift rear end of rear kicking plate to release metal clip, then
rotate front end of rear kicking plate to release pawls and
remove.
: Pawl
: Metal clip
Installation
Installation is in the reverse order of removal.
AWJIA1123ZZ
AWJIA1091ZZ
INT-24
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation.
• When installing rear kicking plate, check that clips and pawls are securely placed into body panel
holes.
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000008969707
REMOVAL
1. Remove front kicking plate. Refer to
INT-22, "KICKING PLATE : Removal and Installation"
.
2. Lift up rear end of dash side finisher to release pawls.
: Pawl
3. Pull back dash side finisher to release dash side finisher from
stud and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the pawls for deformation and damage during installation.
• When installing, check that finisher is aligned with stud bolt located on floor panel.
• When installing dash side finisher, check that pawls are securely placed into body panel holes.
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation
INFOID:0000000008969708
FRONT BODY SIDE WELT
Removal
1. Remove the dash side finisher. Refer to
INT-24, "DASH SIDE FINISHER : Removal and Installation"
.
2. Remove front body side welt.
Installation
Installation is in the reverse order of removal.
REAR BODY SIDE WELT
Removal
1. Remove rear kicking plate. Refer to
INT-22, "KICKING PLATE : Removal and Installation"
2. Remove rear body side welt.
AWJIA1092ZZ
AWJIA1093ZZ
BODY SIDE TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Installation
Installation is in the reverse order of removal.
CENTER PILLAR LOWER FINISHER
CENTER PILLAR LOWER FINISHER : Removal and Installation
INFOID:0000000008969709
REMOVAL
1. Remove front kicking plate and rear kicking plate. Refer to
INT-22, "KICKING PLATE : Removal and
.
2. Remove center pillar lower finisher as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the pawls and clips for deformation and damage during installation. Replace compo-
nent if necessary.
CENTER PILLAR UPPER FINISHER
CENTER PILLAR UPPER FINISHER : Removal and Installation
INFOID:0000000008969710
REMOVAL
CAUTION:
• Be careful not to apply excessive force when removing center pillar upper finisher. Otherwise, clip
may be damaged and fragments may drop in body panels.
1. Slide front seat to the full forward position.
2. Release pawls, using a suitable tool and remove the seat belt
height adjuster finisher (1).
: Pawl
3. Remove front D-ring anchor bolt.
CAUTION:
Before removing D-ring anchor bolt note the positions of washers and spacers for correct installa-
tion.
4. Remove front body side welt and rear body side welt. Refer to
INT-24, "BODY SIDE WELT : Removal and
.
5. Remove center pillar lower finisher. Refer to
INT-25, "CENTER PILLAR LOWER FINISHER : Removal
6. Release center pillar upper finisher upper clip using a suitable tool as shown.
CAUTION:
JMJIA6045ZZ
AWHIA0539ZZ
INT-26
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
When releasing molded in clip, follow the steps as shown to prevent finisher or clip damage.
7. Release center pillar upper finisher lower clip using a suitable
tool (A) and remove.
: Clip
CAUTION:
Do not reuse center pillar upper finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse center pillar upper finisher. Replace with new part for installation.
• When installing center pillar upper finisher, check that clips are securely placed in body panel holes.
PIIB2600J
AWJIA1094ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст