Nissan Versa Note. Instruction — part 219
HOOD LOCK
DLK-161
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (at * mark).
HOOD LOCK RELEASE HANDLE
HOOD LOCK RELEASE HANDLE : Removal and Installation
INFOID:0000000009549385
REMOVAL
1. Remove hood lock/fuel filler door release handle bolts (A).
2. Disconnect hood lock release cable from hood lock/fuel filler door release handle and remove.
INSTALLATION
Installation is in the reverse order of removal.
PIIB5801E
AWKIA2498ZZ
DLK-162
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
Exploded View
INFOID:0000000008969449
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000009486679
REMOVAL
1. Remove inside handle. Refer to
DLK-163, "INSIDE HANDLE : Removal and Installation"
.
2. Remove outside handle. Refer to
DLK-164, "OUTSIDE HANDLE : Removal and Installation"
.
3. Disconnect the harness connector from the door lock actuator.
4. Remove front door glass rear run. Refer to
.
5. Remove bolts and door lock.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door lock bolts.
• After installation, check door open/close, lock/unlock operation.
• Check door lock cables are properly engaged to inside handle and outside handle bracket.
• When installing key cylinder on front door, be sure to rotate key cylinder rod holder until a click is
felt.
1.
Key cylinder (driver side)
2.
Outside handle bracket
3.
Outside handle escutcheon
(passenger side)
4.
Front gasket
5.
Outside handle
6.
Inside handle
7.
Door lock
8.
Key cylinder rod (driver side)
9.
Rear gasket
A.
Clip
B.
Bolt
Pawl
AWKIA2573ZZ
FRONT DOOR LOCK
DLK-163
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check door lock for poor lubrication. Apply a suitable multi-
purpose grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000009486680
REMOVAL
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Partially remove vapor barrier. Refer to
3. Release lock knob (2) and inside handle cable (3) from clip (1)
using a suitable tool.
4. Remove inside handle bolt.
5. Release inside handle (1) from door panel using a suitable tool
and remove.
: Pawl
6. Release inside handle cable (3) and lock cable (2) from inside
handle (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
JMKIA8077ZZ
JMKIA8078ZZ
AWKIA2500ZZ
JMKIA5885ZZ
DLK-164
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
• Check that door lock cables are properly engaged to inside handle.
• After installation, check door open/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009486681
REMOVAL
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Partially remove vapor barrier. Refer to
3. Open rod holder (1) by pulling downward and separate key rod
(3) from door lock assembly (2) (driver side only).
4. Release outside handle cable (1) from cable clip (A).
5. Remove door grommet (1) and bolt from grommet hole (2).
6. While pulling outside handle, remove outside handle escutch-
eon.
JMKIA8080ZZ
AWKIA2574ZZ
JMKIA5888ZZ
JMKIA0560ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст