Nissan Versa Note. Instruction — part 220
FRONT DOOR LOCK
DLK-165
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
7. While pulling outside handle (1), slide toward rear of vehicle.
8. Disconnect the harness connectors from the outside handle and remove.
9. Remove front gasket and rear gasket.
10. Slide outside handle bracket toward rear of vehicle to remove.
: Front
11. Disconnect outside handle cable (1) from outside handle bracket
(2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are properly engaged with outside handle bracket.
• After installation, check door open/close, and lock/unlock operation.
JMKIA0524ZZ
JMKIA5890ZZ
JMKIA5891ZZ
DLK-166
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
REAR DOOR LOCK
Exploded View
INFOID:0000000008969450
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000009486682
REMOVAL
1. Remove inside handle. Refer to
DLK-167, "INSIDE HANDLE : Removal and Installation"
.
2. Remove outside handle. Refer to
DLK-168, "OUTSIDE HANDLE : Removal and Installation"
.
3. Remove bolts (A) from rear door glass rear run (1).
4. Disconnect the harness connector from door lock actuator.
5. Remove bolts and door lock.
1.
Outside handle bracket
2.
Outside handle escutcheon
3.
Front gasket
4.
Outside handle
5.
Inside handle
6.
Door lock
7.
Door lock
A.
Clip
B.
Bolt
Pawl
AWKIA2575ZZ
JMKIA8086ZZ
REAR DOOR LOCK
DLK-167
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door lock assembly bolts.
• After installation, check door open/close, lock/unlock operation.
• Check door lock cable is properly engaged with inside handle and outside handle bracket.
• Check door lock assembly for poor lubrication. If necessary,
apply a suitable multi-purpose grease.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000009486683
REMOVAL
1. Remove rear door finisher. Refer to
INT-18, "Removal and Installation"
.
2. Remove upper portion of vapor barrier. Refer to
.
3. Release lock knob (2) and inside handle cable (3) from clip (1)
using a suitable tool.
4. Remove inside handle bolt.
5. Release inside handle (1) from door panel using a suitable tool
and remove.
: Pawl
JMKIA8087ZZ
JMKIA5704ZZ
AWKIA2500ZZ
DLK-168
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
6. Release inside handle cable (3) and lock cable (2) from inside
handle (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are properly engaged to inside handle.
• After installation, check door open/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009486684
REMOVAL
1. Remove inside handle. Refer to
DLK-167, "INSIDE HANDLE : Removal and Installation"
2. Remove door grommet and bolt from grommet hole.
3. While pulling outside handle, remove outside handle escutch-
eon.
4. While pulling outside handle (1), slide towards rear of vehicle to
remove.
JMKIA5885ZZ
JMKIA1467ZZ
JMKIA5342ZZ
JMKIA0524ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст