Nissan Versa Note. Instruction — part 429
EXL-100
< REMOVAL AND INSTALLATION >
FRONT COMBINATION LAMP
Removal
1. Remove plastic cover.
2. Remove bulb from the front combination lamp.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install the bulb socket securely for watertightness.
SIDE MARKER LAMP BULB
Removal
1. Rotate bulb socket counterclockwise and remove.
2. Remove the bulb from bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install the bulb socket securely for watertightness.
FRONT TURN SIGNAL/PARKING LAMP BULB
Removal
1. Rotate bulb socket counterclockwise and remove.
2. Remove the bulb from bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install the bulb socket securely for watertightness.
FRONT FOG LAMP
EXL-101
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Exploded View
INFOID:0000000009445891
Removal and Installation
INFOID:0000000009445892
REMOVAL
1. Partially remove front fender protector. Refer to
.
2. Disconnect the harness connector from front fog lamp.
3. Remove screws and front fog lamp.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
After installation, perform fog lamp aiming adjustment procedure. Refer to
EXL-97, "Aiming Adjustment Proce-
.
Bulb Replacement
INFOID:0000000009445893
WARNING:
Do not touch bulb by hand while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
REMOVAL
1. Partially remove fender protector. Refer to
1.
Front fog lamp
2.
Front bumper fascia
A.
Front fog lamp bracket
AWLIA2178ZZ
EXL-102
< REMOVAL AND INSTALLATION >
FRONT FOG LAMP
2. Disconnect harness connector (1) from front fog lamp bulb.
3. Rotate the bulb (2) counterclockwise and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install the bulb socket securely for watertightness.
SKIB8304J
COMBINATION SWITCH
EXL-103
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
COMBINATION SWITCH
Removal and Installation
INFOID:0000000009606281
CAUTION:
• Before servicing, turn the ignition switch OFF, disconnect both battery terminals and wait at least
three minutes.
• Do not use air or electric tools when removing or installing the combination switch.
REMOVAL
1. Disconnect the negative and positive battery terminals, then wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
2. Remove the steering column covers. Refer to
IP-17, "Removal and Installation"
.
3. Rotate steering wheel clockwise to access first combination
switch screw (A) and remove.
4. Rotate steering wheel counter-clockwise to access second com-
bination switch screw (A) and remove.
5. Disconnect the harness connector (B) from the combination
switch (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag warning lamp, reset with the self-diagnosis function
and delete the memory with CONSULT.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to
.
ALMIA0648ZZ
ALMIA0649ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст