Nissan Versa Note. Instruction — part 250
HOOD LOCK
DLK-285
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD LOCK
Exploded View
INFOID:0000000009645197
HOOD LOCK
HOOD LOCK : Removal and Installation
INFOID:0000000009645198
REMOVAL
1. Remove hood lock bolts (A).
2. Disconnect hood lock release cable (2) from hood lock (1) and
remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
1.
Hood lock/fuel filler lid release handle
2.
Hood lock assembly
3.
Hood lock release cable assembly
A.
Clip
AWKIA2572ZZ
ALKIA3190ZZ
AWKIA2497ZZ
DLK-286
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD LOCK
• After installation, perform hood assembly adjustment procedure. Refer to
• After adjustment, perform hood lock control inspection. Refer to
.
HOOD LOCK : Inspection
INFOID:0000000009645199
HOOD LOCK INSPECTION
NOTE:
If hood lock cable is bent or deformed, replace it. Refer to
DLK-285, "HOOD LOCK : Removal and Installa-
.
1. Check that secondary latch is properly engage with secondary striker with hoods own weight.
2. While operating hood lock release lever, carefully check that the front end of hood assembly is raised by
approximately 20.0 mm (0.79 in). Also check that hood lock release lever returns to original position.
3. Check that hood lock release lever operates at 49 N (5.0 kg-m, 11.0 ft-lb) or below.
4. Install so that static closing force of hood is 315-490 N (32.1-50.0 kg-m, 70.8-110.2 ft-lb).
5. Check hood lock assembly lubrication condition. If necessary, apply a suitable multi-purpose grease.
HOOD LOCK RELEASE CABLE
HOOD LOCK RELEASE CABLE : Removal and Installation
INFOID:0000000009645200
REMOVAL
1. Disconnect hood lock release cable from hood lock. Refer to
2. Remove radiator cap adapter bracket bolt (A) and radiator reser-
voir tank bolt (B).
3. Remove fender protector (LH). Refer to
EXT-36, "Removal and Installation"
.
4. Release hood lock control cable clips using a suitable tool.
5. Remove hood lock/fuel filler door release handle. Refer to
DLK-161, "HOOD LOCK RELEASE HANDLE :
.
6. Remove dash side finisher (LH). Refer to
INT-24, "DASH SIDE FINISHER : Removal and Installation"
7. Remove grommet on the lower dash and pull the hood lock release cable into the passenger compart-
ment.
CAUTION:
While pulling, be careful not to damage (peel) the outside of the hood lock release cable.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to bend cable too much, keep the radius 100 mm (3.94 in) or more.
• Check that hood lock release cable is properly engaged with hood lock.
JMKIA8027ZZ
HOOD LOCK
DLK-287
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (at * mark).
HOOD LOCK RELEASE HANDLE
HOOD LOCK RELEASE HANDLE : Removal and Installation
INFOID:0000000009645202
REMOVAL
1. Remove hood lock/fuel filler door release handle bolts (A).
2. Disconnect hood lock release cable from hood lock/fuel filler door release handle and remove.
INSTALLATION
Installation is in the reverse order of removal.
PIIB5801E
AWKIA2498ZZ
DLK-288
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
Exploded View
INFOID:0000000009645203
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000009645204
REMOVAL
1. Remove inside handle. Refer to
DLK-289, "INSIDE HANDLE : Removal and Installation"
.
2. Remove outside handle. Refer to
DLK-290, "OUTSIDE HANDLE : Removal and Installation"
.
3. Disconnect the harness connector from the door lock actuator.
4. Remove front door glass rear run. Refer to
.
5. Remove bolts and door lock.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door lock bolts.
• After installation, check door open/close, lock/unlock operation.
• Check door lock cables are properly engaged to inside handle and outside handle bracket.
• When installing key cylinder on front door, be sure to rotate key cylinder rod holder until a click is
felt.
1.
Key cylinder
2.
Outside handle bracket
3.
Front gasket
4.
Outside handle
5.
Inside handle
6.
Door lock
7.
Key cylinder rod
8.
Rear gasket
A.
Clip
B.
Bolt
Pawl
AWKIA2581ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст