Nissan Versa Note. Instruction — part 251
FRONT DOOR LOCK
DLK-289
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check door lock for poor lubrication. Apply a suitable multi-
purpose grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000009645205
REMOVAL
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Partially remove vapor barrier. Refer to
3. Release lock knob (2) and inside handle cable (3) from clip (1)
using a suitable tool.
4. Remove inside handle bolt.
5. Release inside handle (1) from door panel using a suitable tool
and remove.
: Pawl
6. Release inside handle cable (3) and lock cable (2) from inside
handle (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
JMKIA8077ZZ
JMKIA8078ZZ
AWKIA2500ZZ
JMKIA5885ZZ
DLK-290
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
• Check that door lock cables are properly engaged to inside handle.
• After installation, check door open/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009645206
REMOVAL
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Partially remove vapor barrier. Refer to
3. Open rod holder (1) by pulling downward and separate key rod
(3) from door lock assembly (2) (driver side only).
4. Release outside handle cable (1) from cable clip (A).
5. Remove door grommet (1) and bolt from grommet hole (2).
6. While pulling outside handle, remove outside handle escutch-
eon.
JMKIA8080ZZ
AWKIA2574ZZ
JMKIA5888ZZ
JMKIA0560ZZ
FRONT DOOR LOCK
DLK-291
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
7. While pulling outside handle (1), slide toward rear of vehicle to
remove.
8. Remove front gasket and rear gasket.
9. Slide outside handle bracket toward rear of vehicle to remove.
: Front
10. Disconnect outside handle cable (1) from outside handle bracket
(2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are properly engaged with outside handle bracket.
• After installation, check door open/close, and lock/unlock operation.
JMKIA0524ZZ
JMKIA5890ZZ
JMKIA5891ZZ
DLK-292
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
REAR DOOR LOCK
Exploded View
INFOID:0000000009671248
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000009645208
REMOVAL
1. Remove inside handle. Refer to
DLK-293, "INSIDE HANDLE : Removal and Installation"
.
2. Remove outside handle. Refer to
DLK-294, "OUTSIDE HANDLE : Removal and Installation"
.
3. Remove bolts (A) from rear door glass rear run (1).
4. Disconnect the harness connector from door lock actuator.
5. Remove bolts and door lock.
1.
Outside handle bracket
2.
Outside handle escutcheon
3.
Front gasket
4.
Outside handle
5.
Inside handle
6.
Door lock
7.
Door lock
A.
Clip
B.
Bolt
Pawl
AWKIA2575ZZ
JMKIA8086ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст