Nissan Versa Note. Instruction — part 48
AV-184
< BASIC INSPECTION >
[NAVIGATION]
INSPECTION AND ADJUSTMENT
3. Put the points FM and RM (mark) 75 cm (29.5 in) from the points FM0 and RM0 individually.
4. Route the vinyl string through the points FM and RM using a triangle scale, and then fix it at approximately
1.5 m (59 in) on both sides with packing tape.
5. Put the points FL, FR, RL, and RR (mark) to both right and left [vehicle width / 2 + 30 cm (11.8 in)] from the
points FM and RM.
Target line preparation procedure 2
6. Draw the lines of the points FL – RL and FR – RR with vinyl string, and fix it with packing tape.
7. Put a mark on the center of each axle, draw vertical lines to the lines of the points FL – RL and FR – RR
from the marks on the center of the axle using a triangle scale, and then fix the lines using packing tape.
Target line preparation procedure 3
Perform “Calibrating Camera Image”
CONSULT work support
1.
Thread
2.
Weight
3.
Point FM0 (mark)
4.
Point RM0 (mark)
5.
Packing tape (to fix the vinyl string)
6.
Vinyl string
JSNIA0921ZZ
1.
Point FM
2.
Point RM
3.
Triangle scale
4.
Point FL (mark)
5.
Point FR (mark)
6.
Point RL (mark)
7.
Point RR (mark)
A.
75 cm (29.5 in)
B.
Approx. 1.5 m (59 in)
C.
30 cm (11.8 in)
[Vehicle width/ 2 + 30 cm (11.8 in)
from the points FM and RM]
JSNIA0922ZZ
1.
Point FL
2.
Point FR
3.
Point RL
4.
Point RR
5.
Center position of axle
6.
Triangle scale
AV
INSPECTION AND ADJUSTMENT
AV-185
< BASIC INSPECTION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
1. On the CONSULT screen, touch “CALIBRATING CAMERA IMAGE (FRONT CAMERA)”, “CALIBRATING
CAMERA IMAGE (PASS-SIDE CAMERA)”, “CALIBRATING CAMERA IMAGE (DR-SIDE CAMERA)”, or
“CALIBRATING CAMERA IMAGE (REAR CAMERA)” to accept the selection.
NOTE:
To cancel the indication of Incomplete calibration, select items based on the target camera.
2. On the adjustment screen of each camera, adjust the parameter
by touching the “AXIS X” button, “AXIS Y” button, and
“ROTATE” button to place the calibration marker shown on the
camera screen on the target line drawn on the ground.
3. Touch “APPLY” button on the CONSULT screen. “PRCSNG” is
displayed and adjustment results are shown on the camera screen.
CAUTION:
Check that “PRCSNG” is displayed. Never perform other operations while “PRCSNG” is dis-
played.
4. Touch “OK” button on the CONSULT screen. “PRCSNG” is displayed and adjustment results are written to
the around view monitor control unit.
CAUTION:
Check that “PRCSNG” is displayed. Never perform other operations while “PRCSNG” is dis-
played.
>> GO TO 6.
6.
PERFORM “FINE TUNING OF BIRDS-EYE VIEW”
This mode is designed to align the boundary between each camera image that could not be aligned in the
“Calibrating Camera Image” mode.
CONSULT work support
1. Select “FINE TUNING OF BIRDS-EYE VIEW” by touching CONSULT screen.
2. On the adjustment screen of each camera, adjust the parameter
by touching the “AXIS X” button, “AXIS Y” button”, and
“ROTATE” button to place the calibration marker shown on the
camera screen on the target line drawn on the ground.
NOTE:
Touch “SELECT” button on the CONSULT screen to select the
target camera.
3. Touch “APPLY” button on the CONSULT screen. “PRCSNG” is
displayed and adjustment results are shown on the camera
screen.
CAUTION:
Check that “PRCSNG” is displayed. Never perform other
operations while “PRCSNG” is displayed.
4. Touch “OK” button on the CONSULT screen. “PRCSNG” is displayed and adjustment results are written to
the around view monitor control unit.
CAUTION:
• Check that “PRCSNG” is displayed. Never perform other operations while “PRCSNG” is dis-
played.
• After pressing the “OK” button, never press buttons other than the “BACK” button.
NOTE:
• It can be initialized to the NISSAN factory default condition with “Initialize Camera Image Calibration”.
• The adjustment value is cancelled in this mode by performing “Initialize Camera Image Calibration”.
>> Calibration end
Adjustment range
Rotation direction (Center dial)
: 31 patterns (16 on the center)
Upper/lower direction (upper/lower
switch)
:
−22 – 22
Left/right direction (left/right switch)
:
−22 – 22
JSNIA4212ZZ
JSNIA4214ZZ
AV-186
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
U0428 STEERING ANGLE SENSOR
DTC/CIRCUIT DIAGNOSIS
U0428 STEERING ANGLE SENSOR
DTC Logic
INFOID:0000000009694236
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009694237
1.
ADJUST THE NEUTRAL POSITION OF THE STEERING ANGLE SENSOR
When U0428 is detected, adjust the neutral position of the steering angle sensor.
>> Perform adjustment of the neutral position of the steering angle sensor. Refer to
.
CONSULT Display
DTC Detection Condition
Possible Cause
ST ANG SEN CALIB
[U0428]
The neutral position adjustment of the steering
angle sensor is incomplete.
Adjust neutral position of the steering angle sen-
sor.
AV
U1000 CAN COMM CIRCUIT
AV-187
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U1000 CAN COMM CIRCUIT
AV CONTROL UNIT
AV CONTROL UNIT : DTC Logic
INFOID:0000000009460005
DTC DETECTION LOGIC
AV CONTROL UNIT : Diagnosis Procedure
INFOID:0000000009460006
1.
PERFORM SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Perform Self Diagnostic Result for MULTI AV.
Is CAN COMM CIRCUIT displayed?
YES
>> Refer to
LAN-15, "Trouble Diagnosis Flow Chart"
NO
>> Refer to
GI-41, "Intermittent Incident"
.
AROUND VIEW MONITOR CONTROL UNIT
AROUND VIEW MONITOR CONTROL UNIT : DTC Logic
INFOID:0000000009694233
DTC DETECTION LOGIC
AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure
INFOID:0000000009694234
1.
PERFORM SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Perform Self Diagnostic Result for AVM.
Is CAN COMM CIRCUIT displayed?
YES
>> Refer to
LAN-15, "Trouble Diagnosis Flow Chart"
NO
>> Refer to
GI-41, "Intermittent Incident"
.
CONSULT Display
DTC Detection Condition
Possible Cause
CAN COMM CIRCUIT
[U1000]
AV control unit is not transmitting or receiving
CAN communication signal for 2 seconds or
more.
CAN communication system.
CONSULT Display
DTC Detection Condition
Possible Cause
CAN COMM CIRCUIT
[U1000]
Around view monitor control unit is not transmit-
ting or receiving CAN communication signal for 2
seconds or more.
CAN communication system.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст