Nissan Versa Note. Instruction — part 49
AV-188
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
U1010 CONTROL UNIT (CAN)
U1010 CONTROL UNIT (CAN)
AV CONTROL UNIT
AV CONTROL UNIT : DTC Logic
INFOID:0000000009460007
DTC DETECTION LOGIC
AROUND VIEW MONITOR CONTROL UNIT
AROUND VIEW MONITOR CONTROL UNIT : DTC Logic
INFOID:0000000009694235
DTC DETECTION LOGIC
CONSULT Display
DTC Detection Condition
Possible Cause
CONTROL UNIT (CAN)
[U1010]
Error during CAN controller hardware initializa-
tion (VCAN).
Replace the AV control unit if the malfunction oc-
curs constantly.
Refer to
AV-240, "Removal and Installation"
.
CONSULT Display
DTC Detection Condition
Possible Cause
CONTROL UNIT (CAN)
[U1010]
Error during CAN controller hardware initializa-
tion (VCAN).
Replace the Around view monitor control unit if
the malfunction occurs constantly.
Refer to
AV-248, "Removal and Installation"
.
AV
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
AV-189
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000009694238
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009694239
Regarding Wiring Diagram information, refer to
.
1.
CHECK REAR VIEW CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and rear view camera connectors.
3. Check continuity between around view monitor control unit connector B54 and rear view camera connec-
tor D501.
4. Check continuity between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK REAR VIEW CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and rear view camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-248, "Removal and Installation"
3.
CHECK REAR VIEW CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and rear view camera connectors.
CONSULT Display
DTC Detection Condition
Possible Cause
Rear display output signal diag-
nosis (Harness disconnection)
[U111A]
Rear view camera image signal circuit open or
short.
Check rear view camera image signal circuit.
Around view monitor control unit
Rear view camera
Continuity
Connector
Terminals
Connector
Terminals
B54
26
D501
2
Yes
25
1
Around view monitor control unit
Ground
Continuity
Connector
Terminal
B54
26
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
B54
26
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
AV-190
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
3. Check continuity between around view monitor control unit connector B54 and rear view camera connec-
tor D501.
4. Check continuity between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK REAR VIEW CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit and rear view camera connectors.
2. Turn ignition switch ON.
3. Check signal between the terminals of around view monitor control unit connector B54.
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-248, "Removal and Installation"
NO
>> Replace rear view camera. Refer to
AV-250, "Removal and Installation"
.
Around view monitor control unit
Rear view camera
Continuity
Connector
Terminals
Connector
Terminals
B54
28
D501
4
Yes
27
5
Around view monitor control unit
Ground
Continuity
Connector
Terminal
B54
28
No
Around view monitor control unit connector B54
Condition
Reference value
(+)
(
−)
Terminal
Terminal
28
27
CAMERA switch is ON or se-
lector lever in R (reverse).
JSNIA0834GB
AV
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
AV-191
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000009694240
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009694241
Regarding Wiring Diagram information, refer to
.
1.
CHECK RH SIDE CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and RH side camera connectors.
3. Check continuity between around view monitor control unit connector B54 and RH side camera connector
D107.
4. Check continuity between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK RH SIDE CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and RH side camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-248, "Removal and Installation"
3.
CHECK RH SIDE CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and RH side camera connectors.
CONSULT Display
DTC Detection Condition
Possible Cause
Right side display output signal
diagnosis (Harness disconnec-
tion)
[U111B]
Right side camera image signal circuit open or
short.
Check right side camera image signal circuit.
Around view monitor control unit
RH side camera
Continuity
Connector
Terminals
Connector
Terminals
B54
34
D107
2
Yes
33
1
Around view monitor control unit
Ground
Continuity
Connector
Terminal
B54
34
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
B54
34
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст