Nissan Versa Note. Instruction — part 806
TM-104
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F11A]
TCM
*: These monitor items do not use.
TERMINAL LAYOUT
SPORT MODE IND
In overdrive OFF
On
Other than the above
Off
MMODE IND
Always
Off
VDC ON
Always
Off
TCS ON
Always
Off
ABS FAIL SIGNAL
When ABS malfunction signal is received
On
Other than the above
Off
ABS ON
ABS is activated
On
Other than the above
Off
4WD FAIL SIGNAL
Always
Off
4WD OPERATION SIG
Always
Off
4WD-TCS SIGNAL
Always
Off
RANGE
Selector lever: “P” and “N” positions
N/P
Selector lever: “R” position
R
Selector lever: “D” position (OD OFF indicator
lamp OFF)
D
Selector lever: “D” position (OD OFF indicator
lamp ON)
S
Selector lever: “L” position
L
M GEAR POS
Always
1
G SEN SLOPE
Flat road
0%
Uphill gradient
The value changes to the positive side
along with uphill gradient. (Maximum
40.45%)
Downhill gradient
The value changes to the negative side
along with downhill gradient. (Minimum
−
40.45%)
ENGBRKLVL
When the engine brake level of “ENGINE
BRAKE ADJ”. in “Work Support” is ON
On
When the engine brake level of “ENGINE
BRAKE ADJ”. in “Work Support” is OFF
Off
PVIGN VOLT
Ignition switch: ON
10 – 16 V
TRGT AUX GR RATIO
Vehicle started with selector lever in “L” position
1.80
Release the accelerator pedal after the follow-
ing conditions are satisfied
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or less
• Vehicle speed: 50 km/h (31 MPH) or more
1.00
G SEN CALIBRATION
When G sensor calibration is completed
DONE
When G sensor calibration is not completed
YET
N IDLE STATUS
When idle neutral control is operated
On
When idle neutral control is not operated
Off
CVT-B*
—
—
CVT-A*
—
—
Monitor item
Condition
Value/Status (Approx.)
TCM
TM-105
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
INPUT/OUTPUT SIGNAL STANDARD
JSDIA2713ZZ
Terminal No.
(Wire color)
Description
Condition
Value (Approx.)
+
−
Signal
Input/
Output
2
(R/B)
Ground
L range switch
Input
Ignition
switch
ON
Selector lever: “L” position
10
− 16 V
Other than the above
0 V
4
(W/B)
Ground
D range switch
Input
Selector lever: “D” position
10
− 16 V
Other than the above
0 V
5
(L/B)
Ground
N range switch
Input
Selector lever: “N” position
10
− 16 V
Other than the above
0 V
6
(O)
Ground
R range switch
Input
Selector lever: “R” position
10
− 16 V
Other than the above
0 V
7
(Y)
Ground
P range switch
Input
Selector lever: “P” position
10
− 16 V
Other than the above
0 V
11
(LG)
Ground
Sensor ground
Input
Always
0 V
12
(G/W)
Ground
CVT fluid tempera-
ture sensor
Output
Ignition
switch
ON
CVT fluid: Approx. 20
°C
2.01 – 2.05 V
CVT fluid: Approx. 50
°C
1.45 – 1.50 V
CVT fluid: Approx. 80
°C
0.90 – 0.94 V
14
(G/R)
Ground
G sensor
Input
Ignition
switch
ON
When the vehicle stops on
a flat road
2.5 V
15*
(V)
—
—
—
—
—
16
(L/R)
Ground
Secondary pres-
sure sensor
Input
• Selector lever: “N” position
• At idle
0.88 – 0.92 V
21
(R/W)
—
ROM ASSY
(CHIP SELECT)
—
—
—
22
(V)
—
ROM ASSY
(DATA I/O)
—
—
—
23
(P/L)
—
CAN-L
Input/
Output
—
—
24
(BR)
Ground
Output speed sen-
sor
Input
• Selector lever: “L” position
• Vehicle speed: 20 km/h (12 MPH)
200 Hz
JSDIA1904GB
TM-106
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F11A]
TCM
26
(O/W)
Ground
Sensor power sup-
ply
Output
Ignition switch: ON
5.0 V
Ignition switch: OFF
0 V
30
(BR/B)
Ground
Line pressure sole-
noid valve
Output
• After engine warming up
• Selector lever: “N” position
• At idle
• After engine warming up
• Selector lever: “N” position
• Depress the accelerator pedal fully
31
(L/W)
—
ROM ASSY
(CLOCK)
—
—
—
33
(L/G)
—
CAN-H
Input/
Output
—
—
34
(W)
Ground
Secondary speed
sensor
Input
• Selector lever: “L” position
• Vehicle speed: 20 km/h (12 MPH)
700 Hz
35
(LG/R)
Ground
Primary speed sen-
sor
Input
• Selector lever: “L” position
• Vehicle speed: 20 km/h (12 MPH)
1,100 Hz
37
(BR/W)
Ground
High clutch & re-
verse brake sole-
noid valve
Output
In driving at “L” position
Release the accelerator pedal after
the following conditions are satisfied
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or
less
• Vehicle speed: 50 km/h (31 MPH) or
more
Terminal No.
(Wire color)
Description
Condition
Value (Approx.)
+
−
Signal
Input/
Output
JSDIA1897GB
JSDIA1898GB
JSDIA1905GB
JSDIA1906GB
JSDIA1897GB
JSDIA3653GB
TCM
TM-107
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
38
(G)
Ground
Torque converter
clutch solenoid
valve
Output
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or
less
• Vehicle speed: 20 km/h (12 MPH) or
more
• Engine started
• Vehicle is stopped
39
(G/B)
Ground
Low brake solenoid
valve
Output
• Selector lever: “L” position
• Vehicle speed: 20 km/h (12 MPH)
Release the accelerator pedal after
the following conditions are satisfied
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or
less
• Vehicle speed: 50 km/h (31 MPH) or
more
40
(Y/B)
Ground
Primary pressure
solenoid valve
Output
• Selector lever: “L” position
• Vehicle speed: 20 km/h (12 MPH)
41
(B)
Ground
Ground
Output
Always
0 V
42
(B)
Ground
Ground
Output
Always
0 V
45
(LG)
Ground
Battery power sup-
ply (memory back-
up)
Input
Always
10
− 16 V
46
(LG)
Ground
Battery power sup-
ply (memory back-
up)
Input
Always
10
− 16 V
47
(R/W)
Ground
Ignition power sup-
ply
Input
Ignition switch: ON
10
− 16 V
Ignition switch: OFF
0 V
Terminal No.
(Wire color)
Description
Condition
Value (Approx.)
+
−
Signal
Input/
Output
JSDIA1900GB
JSDIA1901GB
JSDIA1902GB
JSDIA1903GB
JSDIA1897GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст