Nissan Almera Tino V10. Instruction — part 575
EC-1126
[YD (WITH EURO-OBD)]
DTC P0341 CMP SENSOR
Diagnostic Procedure
EBS013D9
1.
CHECK STARTING SYSTEM
Turn ignition switch to START position.
Yes or No
Yes
>> GO TO 2.
No
>> Check starting system. (Refer to SC-13, “STARTING SYSTEM”.)
2.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten body ground screw. Refer to
.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace ground connection.
3.
CHECK CMP SENSOR POWER SUPPLY CIRCUIT
1.
Disconnect camshaft position (CMP) sensor harness connector.
2.
Turn ignition switch ON.
3.
Check voltage between CMP sensor terminal 1 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
Does the engine turn over?
Does the starter motor operate?
MBIB0915E
MBIB0907E
Voltage: Approximately 5.3V
MBIB1095E
DTC P0341 CMP SENSOR
EC-1127
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
4.
CHECK CMP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 66 and CMP sensor terminal 2.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK CMP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal 47 and CMP sensor terminal 3.
Refer to Wiring Diagram.
2.
Also check harness for short to ground or short to power.
OK or NG
OK
>> GO TO 6.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.
CHECK CAMSHAFT POSITION SENSOR
Refer to
EC-1128, "Component Inspection"
.
OK or NG
OK
>> GO TO 7.
NG
>> Replace camshaft position sensor.
7.
CHECK CAMSHAFT (EXHAUST)
Check the following.
●
Accumulation of debris to the signal plate of camshaft rear end
●
Chipping signal plate of camshaft rear end
OK or NG
OK
>> GO TO 8.
NG
>> Remove debris and clean the signal plate of camshaft
rear end or replace camshaft.
8.
CHECK INTERMITTENT INCIDENT
Refer to
EC-1002, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Continuity should exist.
Continuity should exist.
MBIB0990E
EC-1128
[YD (WITH EURO-OBD)]
DTC P0341 CMP SENSOR
Component Inspection
EBS013DA
CAMSHAFT POSITION SENSOR
1.
Loosen the fixing bolt of the sensor.
2.
Disconnect camshaft position sensor harness connector.
3.
Remove the sensor.
4.
Visually check the sensor for chipping.
5.
Check resistance as shown in the figure.
6.
If NG, replace camshaft position sensor.
Removal and Installation
EBS013DB
CAMSHAFT POSITION SENSOR
Refer to
.
MBIB0647E
Terminal No. (Polarity)
Resistance
Ω
[at 25
°
C (77
°
F)]
3 (+) - 1 (-)
Except 0
3 (+) - 2 (-)
2 (+) - 1 (-)
Except 0 or
∞
MBIB0616E
DTC P0380 GLOW RELAY
EC-1129
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0380 GLOW RELAY
PFP:25230
On Board Diagnosis Logic
EBS013DC
DTC Confirmation Procedure
EBS013DD
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Wait at least 5 seconds.
4.
If 1st trip DTC is detected, go to
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0380
Glow relay circuit
An excessively low voltage is sent to ECM
through glow relay.
●
Harness or connectors
(The glow relay circuit is open or shorted.)
●
Glow relay
An excessively low voltage is sent to ECM
through glow relay.
●
Harness or connectors
(The glow relay circuit is shorted.)
●
Glow relay
SEF817Y
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст