Nissan Almera Tino V10. Instruction — part 280
Front Door Glass
=NLBT0007
I
Make sure that door glass is positioned in glass run groove.
I
Make sure that there is no abnormality when door glass is
raised or lowered.
FRONT DOOR GLASS AND REGULATOR
NLBT0007S01
NBT086
I
For removal of front door finisher, refer to “DOOR TRIM”,
BT-31.
I
Remove sealing screen.
NBT087
1.
Using power window main switch, raise or lower door glass
until carrier plate securing bolts are visible.
2.
Remove bolts securing carrier plate.
DOOR
Front Door Glass
BT-14
NBT088
3.
Hold door glass with both hands. While raising rear end of door
glass, remove door glass from sash and away from outside the
door.
NBT089
4.
Disconnect regulator assembly connector.
5.
Remove bolts securing regulator assembly and guide rail, then
remove regulator assembly and guide rail.
NBT090
Inspection
NLBT0007S0101
Check regulator assembly for the following parts. Replace faulty
parts with new ones.
I
Wire for wear
I
Regulator for deformation
I
Sliding parts for lubrication
Front Door Limit Switch Reset (Driver side
only)
NLBT0008
RESET CONDITIONS
NLBT0008S01
After each of the following operations are performed, reset the limit
switch (with built-in motor).
I
Regulator removal and installation
I
Removal of motor from regulator
I
Operation of regulator as a single unit
I
Door glass removal and installation
I
Glass run removal and installation
NBT135
RESET PROCEDURES
NLBT0008S02
After installing parts, proceed as follows:
1.
Close the door window completely.
2.
Press the reset switch and open the door window completely.
3.
Release the reset switch. After making sure the reset switch
has returned to the original position, close the door window
completely.
4.
The limit switch is now reset.
CAUTION:
Be sure to instructionly open or close the door window. (Do not
use the automatic open-close procedures.)
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
HA
SC
EL
IDX
DOOR
Front Door Glass (Cont’d)
BT-15
Rear Door Glass
NLBT0009
I
Make sure that door glass is positioned in glass run groove.
I
Make sure that there is no abnormality when door glass is
raised or lowered.
REAR DOOR GLASS AND REGULATOR
NLBT0009S01
NBT092
I
For removal of rear door finisher, refer to “DOOR TRIM”,
BT-31.
I
For removal of door outside molding, refer to “EXTERIOR”,
BT-37.
I
Remove sealing screen.
NBT093
1.
Using power window main switch, raise or lower door glass
until carrier plate securing bolts are visible.
2.
Remove bolts securing main channel.
DOOR
Rear Door Glass
BT-16
YBT114
3.
Remove corner inner cover.
YBT105
4.
Remove nut securing lower sash rear.
NBT097
5.
Remove bolt securing under of lower sash rear.
6.
Remove door glass from glass run and away from outside the
door.
NBT094
7.
Disconnect regulator assembly connector.
8.
Remove bolts securing regulator assembly, then remove regu-
lator assembly.
NBT136
Inspection
NLBT0009S0101
Check regulator assembly for the following parts. Replace faulty
parts with new ones.
I
Wire for wear
I
Regulator for deformation
I
Sliding parts for lubrication
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
HA
SC
EL
IDX
DOOR
Rear Door Glass (Cont’d)
BT-17
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст