Nissan Almera Tino V10. Instruction — part 691
NEL714
Aiming Adjustment
=NLEL0029
Before performing aiming adjustment, make sure of the following.
1)
Keep all tires inflated to correct pressure.
2)
Place vehicle on level ground.
3)
See that vehicle is unloaded (except for full levels of coolant,
engine oil and fuel, and spare tire, jack, and tools). Have the
driver or equivalent weight placed in driver’s seat.
Adjust aiming in the vertical direction by turning the adjusting
screw.
MEL327G
1.
Set the distance between the screen and the center of the fog
lamp lens as shown at left.
2.
Remove front fog lamp rim. For detail, refer to “BODY END” in
BT section.
3.
Turn front fog lamps ON.
NEL716
4.
Adjust front fog lamps so that the top edge of the high inten-
sity zone is 91 to 136 mm (3.58 to 5.35 in) below the height of
the fog lamp centers as shown at left.
I
When performing adjustment, if necessary, cover the head-
lamps and opposite fog lamp.
FRONT FOG LAMP
Aiming Adjustment
EL-60
Wiring Diagram — R/FOG —
NLEL0429
TYPE 1
NLEL0429S01
YEL938D
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
REAR FOG LAMP
Wiring Diagram — R/FOG —
EL-61
TYPE 2
NLEL0429S02
YEL939D
REAR FOG LAMP
Wiring Diagram — R/FOG — (Cont’d)
EL-62
System Description
NLEL0430
TURN SIGNAL OPERATION
NLEL0430S01
Power is supplied at all times
I
through 10A fuse [No. 12, located in fuse block (J/B)]
I
to smart entrance control unit terminal 56, and
I
to combination meter terminal 3.
With the ignition switch in the ON or START position, power is supplied
I
through 10A fuse [No. 10, located in fuse block (J/B)]
I
to smart entrance control unit terminal 29
Ground is supplied to smart entrance control unit terminal 53.
I
through body grounds M28, M48 and M109 (QG engine models) or
I
through body grounds M28, M48 and F51 (YD engine models).
LH Turn
NLEL0430S0101
When the turn signal switch is moved to the L position, ground is supplied from body grounds E24 and E73
I
to smart entrance control unit terminal 25
I
through turn signal switch terminals 3 and 1
With ground is supplied, smart entrance control unit controls the flashing of the LH turn signal lamps.
Power is supplied from smart entrance control unit terminal 64
I
to front turn signal lamp LH terminal 1,
I
to side turn signal lamp LH terminal 2 and
I
to rear combination lamp LH terminal 2
Ground is supplied to the front turn signal lamp LH terminal 2 through body grounds E24 and E73.
Ground is supplied to the side turn signal lamp LH terminal 1 through body grounds E24 and E73.
Ground is supplied to the rear combination lamp LH terminal 1 through body grounds B24, B30 or D89 (LHD
models).
RH Turn
NLEL0430S0102
When the turn signal switch is moved to the R position, ground is supplied from body grounds E24 and E73
I
to smart entrance control unit terminal 26
I
through turn signal switch terminals 2 and 1
With ground is supplied, smart entrance control unit controls the flashing of the RH turn signal lamps.
Power is supplied from smart entrance control unit terminal 63
I
to front turn signal lamp RH terminal 1,
I
to side turn signal lamp RH terminal 2 and
I
to rear combination lamp RH terminal 2
Ground is supplied to the front turn signal lamp RH terminal 2 through body grounds E24 and E73.
Ground is supplied to the side turn signal lamp RH terminal 1 through body grounds E24 and E73.
Ground is supplied to the rear combination lamp RH terminal 1 through body grounds B24, B30 or D89 (LHD
models).
HAZARD LAMP OPERATION
NLEL0430S02
With the hazard switch in the ON position, ground is supplied from body grounds M28 and M48
I
to smart entrance control unit terminal 30
I
through hazard switch terminals 6 and 4
With ground is supplied, smart entrance control unit controls the flashing of the hazard warning lamps.
Power is supplied from smart entrance control unit terminal 64
I
to front turn signal lamp LH terminal 1,
I
to side turn signal lamp LH terminal 2 and
I
to rear combination lamp LH terminal 2
Power is supplied from smart entrance control unit terminal 63
I
to front turn signal lamp RH terminal 1,
I
to side turn signal lamp RH terminal 2 and
I
to rear combination lamp RH terminal 2
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
TURN SIGNAL AND HAZARD WARNING LAMPS
System Description
EL-63
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст