Nissan Almera Tino V10. Instruction — part 196
AT-508
[ALL]
ASSEMBLY
21. Remove paper rolled around input shaft.
22. Install reverse clutch assembly.
●
Align teeth of high clutch drive plates before installing.
23. Install reverse clutch assembly.
●
Align teeth of high clutch drive plates before installing.
Adjustment (2)
ECS009CX
When any parts listed below are replaced, adjust total end play and reverse clutch end play.
TOTAL END PLAY
●
Measure clearance between reverse clutch drum and needle
bearing for oil pump cover.
●
Select proper thickness of bearing race so that end play is within
specifications.
SAT372D
SAT373D
Part name
Total end play
Reverse clutch end
play
Transmission case
●
●
Overrun clutch hub
●
●
Rear internal gear
●
●
Rear planetary carrier
●
●
Rear sun gear
●
●
Front planetary carrier
●
●
Front sun gear
●
●
High clutch hub
●
●
High clutch drum
●
●
Oil pump cover
●
●
Reverse clutch drum
—
●
SAT374D
ASSEMBLY
AT-509
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
1.
Measure dimensions “K” and “L” and then calculate dimension
“J”.
a.
Measure dimension “K”.
b.
Measure dimension “L”.
c.
Calculate dimension “J”.
2.
Measure dimension “M”.
a.
Place bearing race and needle bearing on oil pump assembly.
b.
Measure dimension “M”.
SAT375D
SAT376D
“J”: Distance between oil pump fitting surface of
transmission case and needle bearing mating surface
of high clutch drum.
J = K – L
SAT377D
SAT378D
“M”: Distance between transmission case fitting surface
of oil pump cover and needle bearing on oil pump cover.
“M
1
”: Indication of gauge.
SAT379D
AT-510
[ALL]
ASSEMBLY
c.
Measure thickness of straightedge “t”.
3.
Adjust total end play “T
3
”.
●
Select proper thickness of bearing race so that total end play is within specifications.
REVERSE CLUTCH END PLAY
●
Measure clearance between oil pump cover and thrust washer
for reverse clutch drum.
●
Select proper thickness of thrust washer so that end play is
within specification.
1.
Measure dimensions “O” and “P” and then calculate dimension
“N”.
a.
Place thrust washer on reverse clutch drum.
b.
Measure dimension “O”.
M = M
1
– t
SAT443D
T
3
= J – M
Total end play “T
3
”:
0.25 - 0.55 mm (0.0098 - 0.0217 in)
Bearing races:
Refer to
AT-519, "SERVICE DATA AND SPECIFICATIONS (SDS)"
.
SAT380D
SAT381D
SAT382D
ASSEMBLY
AT-511
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
c.
Measure dimension “P”.
d.
Calculate dimension “N”.
2.
Measure dimensions “R” and “S” and then calculate dimension
“Q”.
a.
Measure dimension “R”.
b.
Measure dimension “S”.
c.
Calculate dimension “Q”.
3.
Adjust reverse clutch end play “T
4
”.
●
Select proper thickness of thrust washer so that reverse clutch end play is within specifications.
“N”: Distance between oil pump fitting surface of trans-
mission case and thrust washer on reverse clutch
drum.
N = O – P
SAT383D
SAT384D
SAT385D
“Q”: Distance between transmission case fitting sur-
face and thrust washer mating surface.
Q = R – S
SAT386D
T
4
= N – Q
Reverse clutch end play:
0.65 - 1.00 mm (0.0256 - 0.0394 in)
Thrust washer: Refer to
AT-519, "SERVICE DATA AND SPECIFICATIONS (SDS)"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст