Nissan Almera Tino V10. Instruction — part 927
SMT940D
SMT951D
22. Pick up EGI harness clamp and install engine slinger. Next, set
chain block.
23. Jack up the air compressor engine bracket.
24. Remove engine front mounting.
25. Remove LH side mounting. Refer to EM-197, “Removal and
Installation”.
SMT952D
26. Jack up until engine oil filter bracket bolts are just about to
touch the side frame.
SMT941D
27. Remove bolts securing transaxle.
28. While the transaxle is suspended, withdraw the transaxle case
from the engine without hitting suspension member.
I
Open the front of the transaxle when the clutch cover
appears. Then, lower the transaxle pulling it toward the
right front.
I
The spacer between the engine and transaxle should be
left at the engine side.
29. Remove spacer.
REMOVAL AND INSTALLATION
RS5F50A
Removal (Cont’d)
MT-22
SMT941D
Installation
NLMT0090S02
1.
Put transaxle under the engine compartment.
2.
Set chain block on transaxle and hang.
3.
Lift up transaxle case so as not to hit against the side frame
and suspension member.
4.
Assemble transaxle to engine.
I
Tighten LH mount, rear side mount and center member bolts.
Refer to EM-197, “Removal and Installation”.
I
Tighten clutch operating cylinder bolts. Refer to CL-15, “Instal-
lation”.
I
Tighten starter motor bolts. Refer to SC-19, “Removal and
Installation”.
I
Install drive shafts. Refer to AX-11, “Installation”.
I
Tighten all transaxle bolts and any part removed.
SMT932D
MODEL YD ENGINE
NLMT0090S0201
Bolt No.
Tightening torque
N·m (kg-m, ft-lb)
“
”
mm (in)
1
40 - 49 (4.0 - 5.0, 29 - 36)
70 (2.76)
2
30.4 - 36.3 (3.1 - 3.7, 23 - 26)
60 (2.36)
3
30.4 - 36.3 (3.1 - 3.7, 23 - 26)
55 (2.17)
GI
MA
EM
LC
EC
FE
CL
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REMOVAL AND INSTALLATION
RS5F50A
Installation
MT-23
NLMT0038
Components
NLMT0038S01
NMT133
1.
Control lever knob
2.
Boot
3.
Control lever socket
4.
Control lever
5.
Bearing seat spring
6.
Seat
7.
Bushing
8.
O-ring
9.
Hand lever socket
10. Plate bolt
11. Transaxle hole cover
12. Mass damper
13. Holder bracket
14. Return spring rubber
15. Return spring
16. Control rod
17. Bushing
18. Collar
19. Bushing
20. Collar
21. Support rod
22. Plate
23. Support rod bracket
TRANSAXLE GEAR CONTROL
RS5F70A, RS5F50A
Components
MT-24
NLMT0054
Case Components
NLMT0054S02
SMT942D
1.
Clutch housing
2.
Dust seal
3.
Oil pocket
4.
Check plug
5.
Input shaft oil seal
6.
Oil channel
7.
Mainshaft front bearing
8.
Bearing retainer
9.
Bushing
10. Reverse idler gear front thrust
washer
11. Reverse idler gear
12. Reverse idler gear bearing
13. Reverse idler gear rear thrust
washer
14. O-ring
15. Reverse idler gear shaft
16. Snap ring
17. Reverse switch
18. Filler plug
19. Side cover gasket
20. Side cover
21. Welch plug
22. Mainshaft bearing snap ring
23. Mainshaft rear bearing adjusting
shim
24. O-ring
25. Rear cover
26. Differential oil seal
27. Drain plug
28. PNP switch
29. Transmission case
30. Oil gutter
31. Welch plug
32. Magnet
33. Boot
34. Striking rod oil seal
35. Welch plug
36. Differential oil seal
37. O-ring
38. Speedometer pinion
GI
MA
EM
LC
EC
FE
CL
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
OVERHAUL
RS5F70A
Case Components
MT-25
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст