Nissan Almera Tino V10. Instruction — part 926
SMT939D
BACK-UP LAMP SWITCH AND PNP SWITCH
NLMT0036S03
— RS5F50A —
NLMT0036S0301
I
Check continuity.
Gear position
Continuity
Reverse
1 - 3
Neutral
2 - 4
Except reverse and neutral
No
ON-VEHICLE SERVICE
RS5F70A, RS5F50A
Position Switch Check (Cont’d)
MT-18
NLMT0008
SMT928D
Removal
NLMT0008S01
CAUTION:
Remove the crankshaft position sensor (POS) from transaxle
assembly before separating transaxle from engine.
Be careful not to damage sensor edge.
1.
Remove battery and its bracket.
2.
Remove air cleaner box with mass air flow sensor.
SMT130DB
3.
Remove clutch operating cylinder from transaxle.
4.
Remove clutch hose clamp.
5.
Disconnect speedometer pinion, back-up lamp, PNP switch
(F70A) harness connectors and ground harness.
6.
Remove starter motor from transaxle.
7.
Remove crankshaft position sensor (POS) from transaxle front
side.
8.
Remove shift control rod and support rod bracket from tran-
saxle.
9.
Drain gear oil from transaxle.
10. Draw out drive shafts from transaxle. Refer to AX-11,
“Removal”.
11. Support engine of transaxle by placing a jack under oil pan.
CAUTION:
Do not place jack under oil pan drain plug.
12. Remove bolts securing center member.
SMT133D
13. Remove LH mount and rear side mounting bolts. Refer to
EM-70, “Removal and Installation”.
14. Remove bolts securing gusset and transaxle.
GI
MA
EM
LC
EC
FE
CL
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REMOVAL AND INSTALLATION
RS5F70A
Removal
MT-19
SMT652C
15. Lower transaxle while supporting it with a jack.
Installation
NLMT0008S02
I
Tighten LH mount, rear side mount and center member bolts.
Refer to EM-70, “Removal and Installation”.
I
Tighten clutch operating cylinder bolts. Refer to CL-15, “Instal-
lation”.
I
Tighten starter motor bolts. Refer to SC-19, “Removal and
Installation”.
I
Install drive shafts. Refer to AX-11, “Installation”.
I
Tighten all transaxle bolts and any part removed.
SMT931D
MODEL QG18DE ENGINE
NLMT0008S0202
Bolt No.
Tightening torque
N·m (kg-m, ft-lb)
“
”
mm (in)
1
31 - 40 (3.1 - 4.1, 23 - 29)
70 (2.76)
2
31 - 40 (3.1 - 4.1, 23 - 29)
80 (3.15)
3
16 - 21 (1.6 - 2.2, 12 - 15)
25 (0.98)
4
31 - 40 (3.1 - 4.1, 23 - 29)
30 (1.18)
A
31 - 40 (3.1 - 4.1, 23 - 29)
20 (0.79)
B
31 - 40 (3.1 - 4.1, 23 - 29)
20 (0.79)
C
15 - 20 (1.5 - 2.1, 11 - 15)
17.5 (0.69)
REMOVAL AND INSTALLATION
RS5F70A
Removal (Cont’d)
MT-20
NLMT0090
SMT928D
Removal
NLMT0090S01
CAUTION:
Remove the crankshaft position sensor (POS) from transaxle
assembly before separating transaxle from engine.
Be careful not to damage sensor edge.
1.
Remove battery and its bracket.
2.
Remove fuse box from battery bracket.
3.
Remove air cleaner box with mass air flow sensor.
4.
Remove air breather hose and vacuum pump hose.
5.
Remove fuel filter bracket bolts.
SMT650CB
6.
Remove terminal and connector from starter motor.
7.
Remove starter motor from transaxle.
8.
Remove clutch hose clamp.
9.
Remove clutch operating cylinder from transaxle.
10. Disconnect speedometer pinion, PNP switch harness connec-
tors and ground harness.
11. Remove crankshaft position sensor (POS) from transaxle front
side.
12. Remove front exhaust tube.
SMT929D
13. Remove shift control rod and support rod bracket from tran-
saxle.
14. Drain gear oil from transaxle.
15. Draw out drive shafts from transaxle. Refer to AX-11,
“Removal”.
16. Support engine and transaxle by placing a jack under the tran-
saxle.
17. Remove bolts securing center member.
SMT950D
18. Take out engine mounting bracket and transaxle installation
bolts. Refer to EM-197, “Removal and Installation”.
19. Remove bolts securing transaxle under side.
20. Temporarily tighten center member.
21. Lower the lift.
GI
MA
EM
LC
EC
FE
CL
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REMOVAL AND INSTALLATION
RS5F50A
Removal
MT-21
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст