Nissan Almera Tino V10. Instruction — part 229
ATC-112
SUNLOAD SENSOR
SUNLOAD SENSOR
PFP:27721
Removal and Installation
EJS0030W
1.
Remove instrument mask (passenger side).
2.
Remove the sunload sensor.
RJIA2330E
INTAKE SENSOR CIRCUIT
ATC-113
C
D
E
F
G
H
I
K
L
M
A
B
ATC
INTAKE SENSOR CIRCUIT
PFP:27723
Removal and Installation
EJS0037L
REMOVAL
1.
Use the refrigerant collecting equipment (for HFC-134a), to dis-
charge the refrigerant from A/C system.
2.
Disconnect low-pressure flexible hose and high-pressure pipe
from the evaporator.
CAUTION:
Cap or wrap the joint of the low-pressure flexible hose and
the high-pressure pipe with a suitable tool such as a vinyl
tape to avoid the entry of air.
3.
Hold expansion valve and move it slightly upward. Push evapo-
rator toward rear of vehicle.
4.
Remove the drain hose and lower case mounting screw.
5.
Swivel rear of lower case toward passenger seat to remove
lower case.
6.
Remove the intake sensor from evaporator.
INSTALLATION
1.
Set expansion valve to cooler grommet.
RJIA1720E
RJIA0189E
RJIA0166E
RJIA0840E
ATC-114
INTAKE SENSOR CIRCUIT
2.
Install evaporator to heater & cooling unit.
3.
Install intake sensor to evaporator.
4.
Install lower cover, then slide evaporator to forward.
5.
Install expansion valve from engine compartment.
RJIA0841E
RJIA0166E
Expansion valve mounting bolts
Tightening torque
: 2.9 - 5.0 N·m (0.30 - 0.50 kg-m,
26 - 44 in-lb)
RJIA0842E
BLOWER UNIT
ATC-115
C
D
E
F
G
H
I
K
L
M
A
B
ATC
BLOWER UNIT
PFP:27200
Removal and Installation
EJS0030Y
REMOVAL
1.
Remove the glove box assembly.
2.
Remove the glove box cover and instrument lower assist panel.
3.
Remove the ECM with ECM bracket.
4.
Remove the blower unit fixing bolt and screw.
5.
Disconnect the blower motor connector, intake door motor con-
nector and auto amp. connector.
6.
Remove the harness fixing clip.
7.
Move the blower unit downwards.
CAUTION:
Slide the blower unit toward the passenger side, remove loca-
tion pins (2 pieces), then move it downwards.
8.
Remove the blower unit.
INSTALLATION
CAUTION:
●
Make sure the location pins (2 pieces) are securely installed.
Disassembly and Assembly
EJS0030Z
NOTE:
This illustration is for RHD models. The layout for LHD models is symmetrically opposite.
RJIA0167E
1.
Auto amplifier
2.
Screw
3.
Cooling hose
4.
Blower fan motor assembly
5.
Washer
6.
Blower fan
7.
Nut
8.
Screw
9.
Intake bellmouth
10. Intake door lever 2
11. Intake door lever 1
12. Intake door link
13. Intake door motor
14. Screw
15. Upper case
16. Intake door 2
17. Intake door 1
18. Adapter assembly
19. Screw
20. Ventilation air filter
21. Filter cover
22. Screw
23. Bracket
24. Screw
25. Under cover clip
26. Screw
RJIA0168J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст