Nissan Murano. Instruction — part 320
DAS-170
< DTC/CIRCUIT DIAGNOSIS >
[BSW]
WARNING SYSTEMS ON INDICATOR CIRCUIT
4.
CHECK WARNING SYSTEMS ON INDICATOR
Check the warning systems ON indicator. Refer to
DAS-170, "Component Inspection"
Is the inspection result normal?
YES
>> Replace the camera control unit. Refer to
DAS-187, "Removal and Installation"
.
NO
>> Replace warning systems switch.
DAS-194, "Removal and Installation"
.
Component Inspection
INFOID:0000000009723377
1.
CHECK WARNING SYSTEMS ON INDICATOR
Apply battery voltage to warning systems switch terminals 1 and 2, and then check if the warning systems ON
indicator illuminates.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the warning systems switch. Refer to
DAS-194, "Removal and Installation"
Terminals
Condition
Warning sys-
tems ON indica-
tor
(+)
(-)
3
2
When the battery voltage is applied
On
When the battery voltage is not applied
Off
DAS
REAR VIEW CAMERA WASHER RELAY CIRCUIT
DAS-171
< DTC/CIRCUIT DIAGNOSIS >
[BSW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
REAR VIEW CAMERA WASHER RELAY CIRCUIT
Component Function Check
INFOID:0000000009723378
1.
CHECK REAR VIEW CAMERA WASHER RELAY CIRCUIT
1.
Turn the ignition switch ON.
2.
Select the ACTIVE TEST item “WASH ACTIVE” of “AVM” with CONSULT.
3.
With operating the test item, check the operation.
Is the inspection result normal?
YES
>> Washer rear view camera washer relay circuit is normal.
NO
>> Refer to
DAS-171, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009723379
1.
CHECK REAR VIEW CAMERA WASHER RELAY 1 POWER SUPPLY CIRCUIT
1.
Turn the ignition switch ON.
2.
Check voltage between rear view camera washer relay 1 harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair rear view camera washer relay 1 power supply circuit.
2.
CHECK REAR VIEW CAMERA WASHER RELAY 1 GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect rear view camera washer relay 1.
3.
Disconnect pump control unit connector.
4.
Check continuity between rear view camera washer relay 1 harness connector and the pump control unit
harness connector.
5.
Check continuity between rear view camera washer relay 1 harness connector and the ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK REAR VIEW CAMERA WASHER RELAY 2 POWER SUPPLY CIRCUIT
1.
Turn the ignition switch ON.
2.
Check voltage between rear view camera washer relay 2 harness connector and ground.
On
: Rear view camera washer is activated.
Off
: Rear view camera washer is not activated.
Terminals
Voltage
(Approx.)
(+)
(
−
)
Rear view camera washer relay 1
Ground
Connector
Terminal
E29
1
Battery voltage
Rear view camera washer
relay 1
Pump control unit
Continuity
Connector
Terminal
Connector
Terminal
E29
2
D170
4
Existed
Rear view camera washer relay 1
Ground
Continuity
Connector
Terminal
E29
2
Not existed
DAS-172
< DTC/CIRCUIT DIAGNOSIS >
[BSW]
REAR VIEW CAMERA WASHER RELAY CIRCUIT
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair rear view camera washer relay 2 power supply circuit.
4.
CHECK REAR VIEW CAMERA WASHER RELAY 2 GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect rear view camera washer relay 2.
3.
Check continuity between rear view camera washer relay 2 harness connector and the pump control unit
harness connector.
4.
Check continuity between rear view camera washer relay 2 harness connector and the ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair harness or connector.
5.
CHECK REAR VIEW CAMERA WASHER RELAY 1 AND 2
Check rear view camera washer relay 1 and 2. Refer to
DAS-172, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace pump control unit.
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000009723380
1.
CHECK REAR VIEW CAMERA WASHER RELAY 1
Apply battery voltage to rear view camera washer relay terminals 1 and 2, and then check for continuity under
the following conditions.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace rear view camera washer relay 1.
2.
CHECK REAR VIEW CAMERA WASHER RELAY 2
Terminals
Voltage
(Approx.)
(+)
(
−
)
Rear view camera washer relay 2
Ground
Connector
Terminal
E28
1
Battery voltage
Rear view camera washer
relay 2
Pump control unit
Continuity
Connector
Terminal
Connector
Terminal
E28
2
D170
3
Existed
Rear view camera washer relay 2
Ground
Continuity
Connector
Terminal
E28
2
Not existed
Terminal
Condition
Continuity
5
3
When the battery voltage is applied
Existed
When the battery voltage is not applied
Not existed
4
3
When the battery voltage is applied
Not existed
When the battery voltage is not applied
Existed
DAS
REAR VIEW CAMERA WASHER RELAY CIRCUIT
DAS-173
< DTC/CIRCUIT DIAGNOSIS >
[BSW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
Apply battery voltage to rear view camera washer relay terminals 1 and 2, and then check for continuity under
the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace rear view camera washer relay 2.
Terminal
Condition
Continuity
5
3
When the battery voltage is applied
Existed
When the battery voltage is not applied
Not existed
4
3
When the battery voltage is applied
Not existed
When the battery voltage is not applied
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст