Nissan Murano. Instruction — part 318
DAS-162
< DTC/CIRCUIT DIAGNOSIS >
[BSW]
U1309 AIR PUMP
U1309 AIR PUMP
DTC Logic
INFOID:0000000009723364
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009723365
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Turn the BSW system ON.
3.
Perform “All DTC Reading” with CONSULT.
4.
Check if the “U1309” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U1309” detected as the current malfunction?
YES
>> Replace the air pump. Refer to
DAS-187, "Removal and Installation"
NO
>> Refer to
GI-44, "Intermittent Incident"
.
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U1309
PUMP INPUT CUR-
RENT JUDGE
Camera control unit detects the value of current from air
pump is incorrect
Air pump
DAS
U130B REAR CAMERA
DAS-163
< DTC/CIRCUIT DIAGNOSIS >
[BSW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
U130B REAR CAMERA
DTC Logic
INFOID:0000000009723366
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn the ignition switch ON.
2.
Shift the selector lever to “R” position.
3.
Perform “All DTC Reading” with CONSULT.
4.
Check if the “U130B” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U130B” detected as the current malfunction?
YES
>> Refer to
DAS-163, "Diagnosis Procedure"
NO
>> Refer to
GI-44, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000009723367
1.
REPLACE REAR VIEW CAMERA
1.
Turn ignition switch OFF.
2.
Replace the rear view camera. Refer to
DAS-188, "Removal and Installation"
3.
Turn ignition switch ON.
4.
Erases All self-diagnosis results.
5.
Shift selector lever to “R” position.
6.
Perform “All DTC Reading” again.
7.
Check if the “U130B” is detected in self-diagnosis results of “AVM”.
Is inspection result normal?
YES
>> Refer to INSPECTION END.
NO
>> Replace camera control unit. Refer to
DAS-187, "Removal and Installation"
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U130B
REAR CAMERA COMM
ERROR
Camera control unit receives the incorrect
communication signal from rear camera unit
• Rear view camera
• Camera control unit
DAS-164
< DTC/CIRCUIT DIAGNOSIS >
[BSW]
U1310 PUMP CONTROL UNIT
U1310 PUMP CONTROL UNIT
DTC Logic
INFOID:0000000009723368
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Turn the BSW system ON.
3.
Perform “All DTC Reading” with CONSULT.
4.
Check if the “U1310” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U1310” detected as the current malfunction?
YES
>> Refer to
DAS-164, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009723369
1.
CHECK VOLTAGE PUMP CONTROL UNIT POWER SUPPLY
Check pump control unit power supply and ground circuit. Refer to
DAS-165, "PUMP CONTROL UNIT : Diag-
.
Is inspection result normal?
YES
>> Replace the pump control unit. Refer to
DAS-189, "Removal and Installation"
.
NO
>> Repair the pump control unit power supply and ground circuit.
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U1310
PUMP ECU JUDGE
If the pump control unit is malfunction
Pump control unit
DAS
POWER SUPPLY AND GROUND CIRCUIT
DAS-165
< DTC/CIRCUIT DIAGNOSIS >
[BSW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
POWER SUPPLY AND GROUND CIRCUIT
CAMERA CONTROL UNIT
CAMERA CONTROL UNIT : Diagnosis Procedure
INFOID:0000000009723370
1.
CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Be sure to eliminate cause of malfunction before installing new fuse.
2.
CHECK CAMERA CONTROL UNIT POWER SUPPLY CIRCUIT
Check voltage between camera control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the camera control unit power supply circuit.
3.
CHECK CAMERA CONTROL UNIT GROUND CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect the camera control unit connector.
3.
Check for continuity between camera control unit harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair the camera control unit ground circuit.
PUMP CONTROL UNIT
PUMP CONTROL UNIT : Diagnosis Procedure
INFOID:0000000009723371
1.
CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
Power source
Fuse No.
Battery power supply
6
Ignition signal
3
Terminal
Condition
Standard
voltage
Reference
voltage
(Approx.)
(+)
(–)
Camera control unit
Ignition
switch
Connector
Terminal
Connector
Terminal
B92
2
B92
1
OFF
9.5 - 16 V
Battery volt-
age
3
OFF
0 - 0.1 V
0 V
ON
9.5 - 16 V
Battery volt-
age
Camera control unit
Ground
Continuity
Connector
Terminal
B92
1
Existed
Power source
Fuse No.
Ignition power supply
47
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст