Nissan Murano. Instruction — part 290
DAS-50
< BASIC INSPECTION >
[LDW]
ACTION TEST
NOTE:
After the operating conditions of warning are satisfied, the warning continues until the vehicle speed
reaches approximately 60 km/h (40 MPH). Refer to
>> INSPECTION END
Approx. 70
km/h (45
MPH) or more
Close to lane marker
Warning
• Buzzer sounds
• Warning lamp
blinks
ON
Short con-
tinuous
beeps
• Close to lane marker
• Turn signal ON (Deviate
side)
No action
ON
—
Vehicle condition/ Driver's operation
Action
Warning sys-
tems ON indi-
cator
Indication on the combination
meter
Buzzer
JPOIA0022GB
JPOIA0021GB
DAS
ADDITIONAL SERVICE WHEN REPLACING CAMERA CONTROL UNIT
DAS-51
< BASIC INSPECTION >
[LDW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ADDITIONAL SERVICE WHEN REPLACING CAMERA CONTROL UNIT
Description
INFOID:0000000009723228
• Always perform the camera control unit configuration after replacing the camera control unit.
• Always perform the rear view camera calibration after removing and installing or replacing the rear view
camera.
• Always perform the rear view camera calibration after replacing the camera control unit.
CAUTION:
The system does not operate normally unless the rear view camera calibration is performed. Always
perform it.
Work Procedure
INFOID:0000000009723229
1.
CAMERA CONTROL UNIT CONFIGURATION
Perform the camera control unit configuration with CONSULT. Refer to
.
>> GO TO 2.
2.
REAR VIEW CAMERA CALIBRATION
Perform the rear view camera calibration with CONSULT. Refer to
DAS-53, "Work Procedure (Preparation)"
.
>> GO TO 3.
3.
PERFORM SELF-DIAGNOSIS
Perform the self-diagnosis of camera control unit with CONSULT (AVM). Check if any DTC is detected.
Is any DTC detected?
YES
>> Perform the trouble diagnosis for the detected DTC. Refer to
.
NO
>> GO TO 4.
4.
LDW SYSTEM ACTION TEST
1.
Perform the LDW system action test. Refer to
2.
Check that the LDW system operates normally.
>> WORK END
DAS-52
< BASIC INSPECTION >
[LDW]
CONFIGURATION (CAMERA CONTROL UNIT)
CONFIGURATION (CAMERA CONTROL UNIT)
Description
INFOID:0000000009723230
• Since vehicle specifications are not included in the camera control unit after replacement, it is required to
write vehicle specifications with CONSULT.
• Configuration has three functions as follows.
Work Procedure
INFOID:0000000009723231
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “Before Replace ECU”, and save the current vehicle specification in CONSULT.
>> GO TO 2.
2.
REPLACE CAMERA CONTROL UNIT
Replace camera control unit. Refer to
DAS-94, "Removal and Installation"
.
>> GO TO 3.
3.
WRITE VEHICLE SPECIFICATION
CONSULT Configuration
Write vehicle specification into camera control unit.
To write vehicle specification stored in CONSULT into the camera control unit>>GO TO 4.
To write vehicle specification into the camera control unit by hand>>GO TO 5.
4.
WRITE STORED DATA
CONSULT Configuration
Select “After Replace ECU” in “Read/Write Configuration.” Write data stored in CONSULT with the “Before
Replace ECU” function into the camera control unit.
>> GO TO 6.
5.
MANUALLY WRITE VEHICLE SPECIFICATION
CONSULT Configuration
Perform “Instruction Configuration.” to write vehicle specification into the camera control unit.
NOTE:
If selection items are not displayed on the CONSULT screen, touch “NEXT”.
>> GO TO 6.
6.
OPERATION CHECK
Check that the operation of the camera control unit and camera images (fixed guide lines and predictive
course lines) are normal.
>> WORK END
Function
Description
Read/Write Configuration
Before Replace ECU
Allows the reading of vehicle specification written in camera con-
trol unit to store the specification in CONSULT.
After Replace ECU
Allows the writing of the vehicle information stored in CONSULT
into the camera control unit.
Instruction Configuration
Allows the writing of the vehicle specification into the camera con-
trol unit by hand.
DAS
CALIBRATING CAMERA IMAGE (REAR VIEW CAMERA)
DAS-53
< BASIC INSPECTION >
[LDW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
CALIBRATING CAMERA IMAGE (REAR VIEW CAMERA)
Description
INFOID:0000000009723232
• Always perform the rear view camera calibration after removing and installing or replacing the rear view
camera.
• Always perform the rear view camera calibration after replacing the camera control unit.
CAUTION:
• Place the vehicle on level ground when the calibration is operated.
• Follow the CONSULT when performing the calibration. (Rear view camera calibration cannot be
operated without CONSULT.)
Work Procedure (Preparation)
INFOID:0000000009723233
1.
PERFORM SELF-DIAGNOSIS
Perform self-diagnosis of the camera control unit with CONSULT (AVM).
Is any DTC detected?
Except “U1308”>>Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to
.
“U1308” or no DTC>>GO TO 2.
2.
PREPARATION BEFORE REAR VIEW CAMERA CALIBRATION
1.
Perform pre-inspection for diagnosis. Refer to
DAS-47, "Inspection Procedure"
.
2.
Adjust the tire pressure to the specified pressure value.
3.
Maintain no-load in vehicle.
4.
Check if coolant and engine oil are filled up to correct level and fuel tank is full.
5.
Shift the selector lever to “P” position and release the parking brake.
6.
Clean the rear view camera.
>> GO TO 3.
3.
PREPARATION OF CALIBRATION TARGET MARK
1.
Prepare six sheets of white paper and black paper, respectively, with dimensions of 200 mm (7.87 in)
×
200 mm (7.87 in) to create a left target, right target, and center target.
NOTE:
Correct the magnification of print and print the target mark sample in the service instruction on the black
paper. Refer to
DAS-57, "Work Procedure (Target Mark Sample)"
.
2.
Tape two sheets of black paper and two sheets of white paper
together to make a target of 400 mm (15.75 in)
×
400 mm (15.75
in).
NOTE:
Use a transparent tape.
3.
Create two more targets according to step 2.
W
: 200 mm (7.87 in)
L
: 200 mm (7.87 in)
JSOIA0635ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст