Nissan Murano. Instruction — part 289
DAS-46
< BASIC INSPECTION >
[LDW]
DIAGNOSIS AND REPAIR WORK FLOW
The customers are not professionals. Never assume that “maybe the customer means···” or “maybe the cus-
tomer mentioned this symptom”.
>> GO TO 2.
2.
SELF-DIAGNOSIS WITH CONSULT
1.
Perform “All DTC Reading” with CONSULT.
2.
Check if the DTC is detected on the self-diagnosis results of “AVM”.
3.
When DTC is detected, follow the instructions below:
-
Record DTC and Freeze Frame Data.
Is any DTC detected?
YES
>> GO TO 5.
NO
>> GO TO 3.
3.
PRE-INSPECTION FOR DIAGNOSIS
Perform pre-inspection for diagnosis. Refer to
DAS-47, "Inspection Procedure"
>> GO TO 4.
4.
ACTION TEST
Perform LDW system action test to check the operation status. Refer to
>> GO TO 6.
5.
TROUBLE DIAGNOSIS BY DTC
1.
Check the DTC in the self-diagnosis results.
2.
Perform trouble diagnosis for the detected DTC. Specify a malfunctioning part. Refer to
(AVM).
>> GO TO 8.
6.
SYMPTOM DIAGNOSIS
Perform symptom diagnosis. Specify malfunctioning part. Refer to
.
>> GO TO 7.
7.
MALFUNCTION PART REPAIR
Repair or replace the identified malfunctioning parts.
>> GO TO 8.
8.
REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT)
Perform self-diagnosis with CONSULT. Check that any DTC is not detected. Erase DTC if DTC is detected
before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES
>> GO TO 5.
NO
>> GO TO 9.
9.
REPAIR CHECK (ACTION TEST)
Perform LDW system action test. Also check the system operation.
Does it operate normally?
YES
>> INSPECTION END
NO
>> GO TO 4.
DAS
PRE-INSPECTION FOR DIAGNOSIS
DAS-47
< BASIC INSPECTION >
[LDW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
PRE-INSPECTION FOR DIAGNOSIS
Inspection Procedure
INFOID:0000000009723224
1.
CHECK REAR VIEW CAMERA LENS
Are rear view camera lens contaminated with foreign materials?
YES
>> Clean rear view camera lens.
NO
>> GO TO 2.
2.
CHECK REAR VIEW CAMERA INSTALLATION CONDITION
Check rear view camera installation condition (e.g. position, looseness, bent in back door).
Is it properly installed?
YES
>> INSPECTION END
NO
>> Install rear view camera properly, and perform rear view camera calibration. Refer to
DAS-48
< BASIC INSPECTION >
[LDW]
REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION INSPECTION
REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION INSPECTION
Inspection Procedure
INFOID:0000000009723225
1.
CHECK REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION
1.
Start the engine.
2.
Select the ACTIVE TEST item “AIR&WASH ACTIVE” of “AVM” with CONSULT.
NOTE:
Before function check, perform the following items:
• Fill with washer fluid.
• Perform ACTIVE TEST item “WASH ACTIVE” of “AVM” with CONSULT for 4 seconds.
3.
With operating the test item, check the operation.
Is it properly operated?
Washer fluid ejects 2 or 3 times. (Normal function)>>INSPECTION END.
Washer fluid ejects 4 times or more.>>Properly install or replace air tube.
Washer fluid ejects only once>> Properly install or replace air tube.
Washer fluid does not eject>>Properly install washer tube or replace washer tube and check valve.
DAS
ACTION TEST
DAS-49
< BASIC INSPECTION >
[LDW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ACTION TEST
Description
INFOID:0000000009723226
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
Fully understand the following items well before the road test;
• Precautions: Refer to
DAS-6, "FOR USA AND CANADA : Precaution for LDW System Service"
.
• System description for LDW: Refer to
.
• Handling precaution: Refer to
DAS-20, "Precautions for Lane Departure Warning"
.
Inspection Procedure
INFOID:0000000009723227
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
Fully understand the following items well before the road test;
• Precautions: Refer to
DAS-6, "FOR USA AND CANADA : Precaution for LDW System Service"
.
• System description for LDW: Refer to
.
• Handling precaution: Refer to
DAS-20, "Precautions for Lane Departure Warning"
.
1.
CHECK LDW SYSTEM SETTING
1.
Start the engine.
2.
Check that the LDW system setting can be enabled/disabled on the navigation screen.
3.
Turn OFF the ignition switch and wait for 30 seconds or more.
4.
Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.
ACTION TEST FOR LDW
1.
Enable the setting of the LDW system on the navigation screen.
2.
Turn warning systems switch ON (warning systems ON indicator is ON).
3.
Check the LDW operation according to the following table.
Vehicle condition/ Driver's operation
Action
Warning sys-
tems ON indi-
cator
Indication on the combination
meter
Buzzer
Less than Ap-
prox. 60 km/h
(40 MPH)
Close to lane marker
No action
ON
—
JPOIA0021GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст