Nissan Murano. Instruction — part 1286
SIDE CURTAIN AIR BAG MODULE
SR-49
< REMOVAL AND INSTALLATION >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE CURTAIN AIR BAG MODULE
Exploded View
INFOID:0000000009720419
Removal and Installation
INFOID:0000000009720420
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove the headlining.
• Normal roof models: Refer to
INT-26, "NORMAL ROOF : Removal and Installation"
.
• Sunroof models: Refer to
INT-30, "SUNROOF : Removal and Installation"
2.
Disconnect the side curtain air bag harness connector.
CAUTION:
• For installing/removing the side curtain air bag harness
connector, insert thin screwdriver wrapped in tape into
notch, lift lock and remove the connector.
• Install the connector with lock raised, and push lock into
the connector.
• After installing the connector, check that the lock is
pushed securely into it.
1.
Side curtain air bag inflator
: N·m (kg-m, ft-lb)
JMHIA1684GB
PHIA0953J
SR-50
< REMOVAL AND INSTALLATION >
[FOR MEXICO]
SIDE CURTAIN AIR BAG MODULE
3.
Remove the fixing bolts, and then remove the side curtain air bag module.
CAUTION:
• Never impact the side curtain air bag module.
• Replace the side curtain air bag module if it has been dropped
or sustained an impact.
• Never insert any foreign objects (screwdriver, etc.) into the side curtain air bag module.
• Never disassemble the side curtain air bag module.
• Never expose the side curtain air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the side curtain air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0009ZZ
CRASH ZONE SENSOR
SR-51
< REMOVAL AND INSTALLATION >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CRASH ZONE SENSOR
Exploded View
INFOID:0000000009720421
Removal and Installation
INFOID:0000000009720422
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove the radiator cover grill RH. Refer to
.
2.
Remove the air duct (inlet). Refer to
3.
Remove the crash zone sensor fixing nuts.
4.
Disconnect the crash zone sensor harness connector, and then remove the crash zone sensor.
CAUTION:
• Never impact the crash zone sensor.
• Replace the crash zone sensor if it has been dropped or sus-
tained an impact.
• Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger air
bag.
INSTALLATION
1.
Crash zone sensor
A.
Crash zone sensor harness connector
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA0515GB
JMHIA0009ZZ
SR-52
< REMOVAL AND INSTALLATION >
[FOR MEXICO]
CRASH ZONE SENSOR
Install in the reverse order of removal.
CAUTION:
• Never use the old fixing nuts after removal, replace with the new nuts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст